The influence of rare earth element (RE) Y on the microstructure and corrosion behavior of extruded AZ91 Mg alloy was surveyed via morphology characterization and corrosion performance measurements. The results indicate the corrosion resistance of the transversal section of AZ91 Mg alloy containing Y was improved compared with AZ91 Mg alloy without Y. The corrosion resistance of the longitudinal section of AZ91 Mg alloy with Y was lower than that of AZ91 Mg alloy without Y. The change of corrosion resistance can be attributed to the dispersion and volume fraction of the second phase, the effect of cathodic reduction rate, and the refined second phase.
29 November 2025 in Advanced Composites and Hybrid Materials
The rational design of heterogeneous interfaces in multilayered structures to enhance interfacial polarization, combined with the strategy of electromagnetic wave (EMW) propagation pathways within composites, represents an effective approach to overcoming the limitations of electromagnetic wave absorption (EMWA) performance. In this work, a multi-interface EMW absorber with a unique EMW transmission pathway was designed, based on the distinctive hollow octahedral structure of MIL-101 and its integration with various microstructural configurations. Multicomponent composites were fabricated via hydrothermal synthesis and electrostatic self-assembly. By leveraging the unique properties of each component, multiple heterogeneous interfaces were constructed, effectively promoting interfacial charge transfer and significantly enhancing interfacial polarization, which in turn facilitates the conversion of electromagnetic energy into heat. The results demonstrate that the RLmin of the prepared CoFe2O4@MIL-101@MoS2/GO (CFMMG, and GO stands for Graphene Oxide) is -55.13 dB, with a thickness of 2.69 mm at 11.4 GHz, while the EAB at 2.37 mm reached 6.3 GHz (9.8–16.1 GHz). Furthermore, first-principles density functional theory (DFT) simulations were conducted to theoretically elucidate the influence of interfacial polarization on the enhanced EMWA capability. This study provides distinctive insights into multi-interface composite cooperation in EMWA engineering.
A new NO2 nanohybrid of a gas sensor (CTAB-MoS2/rGO) was constructed for sensitive room-temperature detection of NO2 by 3D molybdenum disulfide (MoS2) and reduced graphene oxide (rGO), assisted with hexadecyl trimethyl ammonium bromide (CTAB). In comparison with MoS2 and MoS2/rGO, the BET and SEM characterization results depicted the three-dimensional structure of the CTAB-MoS2/rGO nanohybrid, which possessed a larger specific surface area to provide more active reaction sites to boost its gas-sensing performance. Observations of the gas-sensing properties indicated that the CTAB-MoS2/rGO sensor performed a high response of 45.5% for 17.5 ppm NO2, a remarkable selectivity of NO2, an ultra-low detection limit of 26.55 ppb and long-term stability for a 30-day measurement. In addition, the response obtained for the CTAB-MoS2/rGO sensor was about two to four times that obtained for the MoS2/rGO sensor and the MoS2 sensor toward 8 ppm NO2, which correlated with the heterojunction between MoS2 and rGO, and the improvement in surface area and conductivity correlated with the introduction of CTAB and rGO. The excellent performance of the CTAB-MoS2/rGO sensor further suggested the advantage of CTAB in assisting a reliable detection of trace NO2 and an alternative method for highly efficiently detecting NO2 in the environment.
For transient mixed Elastohydrodynamic lubrication (EHL) problems, a novel solution is required to predict friction loss and wear in sliding or rolling parts. However, existing solutions have numerous limitations. In general, the lower the oil film thickness is, the more serious the non-linear problem is. This paper presents an efficient solution to tackle the non-linearity of the mixed EHL problem. The elastic deformation in the fluid–solid iteration coupling problem is divided into two parts: One is induced by the hydrodynamic pressure. This part of the deformation is obtained by the unsteady EHL-FBNS (Fischer–Burmeister–Newton–Schur) solver by considering both mass-conserving cavitation and elastic deformation. The other part of the deformation is introduced by the asperity contact pressure. It can be obtained by the Newton–Raphson method. After some limited iterations, the mixed EHL problems can be solved by evaluating the residual total pressure (including hydrodynamic pressure and asperity contact pressure). The proposed methodology was validated against the results from the published literature and applied to characterize the tribological performance of point contact with moving texturing. It appears that the developed method can be effectively used for tracking the tribological behavior of friction pairs.
Microwave technology is commonly used in many fields such as wireless communication and medical treatment, which are closely related to social development. However, electromagnetic pollution caused by microwaves is gradually increasing and the demand for high-performance microwave absorption materials is also increasing. Porous materials obtained by the pyrolysis of metal–organic frameworks (MOFs) at high temperatures exhibit good conductivity and magnetism, and the original skeleton structure of MOFs can be maintained; thus, MOF-derived materials can be considered viable candidates of microwave absorption materials. In this paper, Fe-CN@CoCN materials were prepared by pyrolyzing a ferrocene (Fc)-doped core–shell zeolite imidazole framework (Fc-ZIF-8@ZIF-67) at 700, 800, and 900 °C for 2 h in an Ar atmosphere. The obtained Fe-CN@CoCN-0.25-700 nanocomposite exhibited excellent microwave absorption (MA) performance with a minimum reflection loss (RLmin) of −42.27 dB at 5.68 GHz and an effective absorption bandwidth (EAB, RL < −10 dB) of 4.80 GHz at a thickness of 2.5 mm. The Fe-CN@CoCN-0.25-800 nanocomposite possessed optimized MA properties with an RLmin of −40.78 dB at 12.56 GHz and an EAB of 4.16 GHz at relatively low thickness of 2 mm. Fe-CN@CoCN nanocomposites are expected to be efficient materials for microwave absorption coatings.