Once the miniaturization of high-performance magnetic resonance imaging (MRI) scanner was accomplished, extremely stringent indexes were needed for the magnetic field, the operational stability and mechanical strength. We adopted “No-insulation (NI) winding technology” to build high-temperature superconducting (HTS) magnets for 3-T grade MRI, in order to achieve these stringent indexes. To realize a compact size of 3-T MRI, the electromagnetic stress of HTS magnet becomes a technical challenge. In this paper, we investigated the construction of an electromagnetic stress reinforced structure for HTS magnets of 3-T MRI. First, the electromagnetic force was estimated, and the distributions of stress and strain induced by electromagnetic force in the winding part of the HTS magnet were reproduced using a finite element analysis. Meanwhile, the influences of the interlayers between sub-coils, shells and blind flanges on the stress property of HTS magnet were evaluated. Based on these results, the material and its consumed volume established the reinforced structure employed of the HTS magnet were also clarified. Finally, the utility of reinforced structure was verified for NI HTS magnets deployed in 3-T MRI.
3 September 2021 in IEEE Transactions on Applied Superconductivity
In this paper, an approach for minimizing stress concentration by optimizing the cross section of a toroidal magnet to D-type is presented. To attempt, the magnetic field distributions of both toroidal and D-shaped toroidal magnets were evaluated and compared using the finite element method (FEM), and a convergence curve of maximal magnetic field effect on the winding part was established. We also reproduced an optimal scheme of the `D-type' toroidal HTS magnet for a 400 MJ grade SMES based on this convergence curve, and evaluated the distribution of electromagnetic stress in the winding of the magnet, including von-mise stress and hoop stress. We next constructed a reinforcement structure for the `D-type' toroidal HTS magnet and investigated the effect of the reinforcement structure material on the suppression of the stress inside the magnet. According these results, an industrialized scheme on the stress inhibition for the D-type HTS magnet for 400 MJ grade SMES was summarized.
5 March 2019 in IEEE Transactions on Applied Superconductivity
ITER is the largest global cooperation project, which will be built as the world's largest tokamak to explore the commercial production of fusion-based electricity. In order to connect the busbars electrically and hydraulically, the “shaking hands“ twin-box type joint were designed and implemented for ITER project. Difference from the conventional method, the indium bonding technology was developed to instead of the Tin soldering method for the joint connection. In order to qualify of the ITER Correction Coil (CC) feeder joint structure and the manufacturing technology, ASIPP has launched the joint qualification on the manufacture process and the cryogenic performance. By means of the indium bonding, the joint resistance can be lower than 1 nΩ before and after the mechanical fatigue. This paper reports the structure and manufacturing process of CC feeder joint, describes the establishing of the testing setup, and finally discusses the cryogenic testing results. Besides the joint resistance, the pressure drop and the critical temperature are reported.
15 February 2022 in IEEE Transactions on Applied Superconductivity
High-performance superconducting joints are essential for the continuous and stable operation of superconducting magnet systems to generate stable magnetic fields, because the local heating from resistive losses can cause the superconductor to enter an unstable regime and result in quench. The China fusion engineering test reactor has five internal joints for each toroidal field coil. To provide a lower heat load of the joints to the cryogenic system, the direct current (dc) resistance of the internal joint connection must be below 0.3 nΩ. At the same time, the structure of the joint jacket should be convenient for winding. The internal joints must fit a space envelope equivalent to the original conductor cross section and must have enough structural strength and a low pressure drop. In the basic design, two trial joints were manufactured and tested at ASIPP. This article provides a description of the design, simulation, and manufacturing process of the trial joint, and finally obtained the test results with electrical resistances of 0.057 and 0.076 nΩ.
9 March 2023 in Journal of Low Temperature Physics