Al7075/10 wt% TiO2 alloy composite has been fabricated by the stir casting method to investigate the influence of wear parameters. The microstructure of the produced composite was analyzed by scanning electronic microscopy. A pin-on-disc rig was used to carry out the wear test on produced composite under dry sliding conditions. The three wear control parameters such as load, sliding velocity and sliding distance were chosen to study the effects on the wear rate and coefficient of friction of composite. The experiments were planned as per L9 orthogonal array based on Taguchi’s design of experiments. The signal-to-noise ratio and analysis of variance techniques were employed to determine the optimum combination of parameters and the significant contribution of each parameter on the responses. The results exposed that the load was the most predominant factor affecting the wear rate and coefficient of friction followed by the sliding distance and sliding velocity. Finally, the regression equations were developed to predict the responses. The worn surface morphology of composite noticed that TiO2 reinforcement protects the matrix alloy from removal of material at all conditions. This investigation revealed that the wear resistance of the Al7075 alloy can be enhanced by the incorporation of TiO2 particles.
7 July 2021 in Surface Topography: Metrology and Properties
This work aims to apply data-driven approach [decision tree (DT) algorithm] to analyse the wear rate (WR) of ZnO-filled AA7075 composites. The results of model-based analysis was compared with Taguchi analysis. Stir casting was used to produce the composite samples. Characterization studies were conducted to analyse the composition and morphology. The scanning electron microscopy results indicated the even dispersion of ZnO in the AA7075. The energy-dispersive x-ray spectroscopy pattern ensures the presence of matrix elements and the inclusion of reinforcement particles into the proposed composites. To minimize the number of experimentation, L27 Orthogonal array is used for finding WR. The ‘DuCom’ Pin-on-Disc apparatus were used to prepare WR data for the set of the proposed composites. Taguchi technique reveals the optimum level factors for obtaining the minimum ‘WR’ is reinforcement content of 10 wt.%, applied load (P) at 10 N, sliding velocity (V) at 1 m s −1 and sliding distance (D) of 1000 m. The experiments results from DT algorithm, and analysis of variance and signal-to-noise ratio analysis from Taguchi-based approach confirmed that reinforcement is the primary element for affecting wear of the composites. The reason for applying DT algorithm is that, the low-level knowledge could be converted into high-level knowledge (If-then-else rules), which can be effortlessly explicable by semiskilled personnel.
Aluminium alloy composites are most popular owing to their versatile applications like high performance parts in aerospace, automotive and marine industries. The intent of current research work is, to predict the optimal parameters for dry sliding wear behaviour of AA8011 matrix composites by using multi attribute decision making method. The varying proportions of zirconia (ZrO 2 ) particles filled composites such as AA8011-5 wt.% ZrO 2 , AA8011-10 wt.% ZrO 2 and AA8011-15 wt.% ZrO 2 were synthesized through stir casting method. The microstructure of the proposed composites taken by scanning electron microscopy (SEM), and it was ensure the presence of reinforcement particles homogeneously distributed within the matrix alloy. The produced composites were subjected to conduct the dry sliding wear test by using pin-on-disc test rig. During the experiments, four wear control parameters with three levels namely, reinforcement (5 wt.%, 10 wt.% and 15 wt.%), applied load (9.81 N, 19.62 N and 29.43 N), sliding velocity (0.94 m/s, 1.88 m/s and 3.76 m/s) and sliding distance (1000 m, 1500 m and 2000 m) were used. A Taguchi coupled TOPSIS method was employed to predict the multiple responses such as wear rate (WR) and coefficient of friction (COF) of produced composites. Experimental result has been observed that, the reinforcement content was the most remarkable parameter on WR and COF with contribution of 55.06%, subsequently by applied load and sliding velocity with contribution of 26.32% and 12.84% respectively. The worn out surfaces of the tested composite was investigated through SEM analysis.