Centre for Materials Engineering and Regenerative Medicine, Bharath Institute of Higher Education and Research, Selaiyur, Chennai 600073, Tamil Nadu, India
Auto-generated profile, based on publicly available information
V. Mohanavel
Centre for Materials Engineering and Regenerative Medicine, Bharath Institute of Higher Education and Research, Selaiyur, Chennai 600073, Tamil Nadu, India
This work aims to apply data-driven approach [decision tree (DT) algorithm] to analyse the wear rate (WR) of ZnO-filled AA7075 composites. The results of model-based analysis was compared with Taguchi analysis. Stir casting was used to produce the composite samples. Characterization studies were conducted to analyse the composition and morphology. The scanning electron microscopy results indicated the even dispersion of ZnO in the AA7075. The energy-dispersive x-ray spectroscopy pattern ensures the presence of matrix elements and the inclusion of reinforcement particles into the proposed composites. To minimize the number of experimentation, L27 Orthogonal array is used for finding WR. The ‘DuCom’ Pin-on-Disc apparatus were used to prepare WR data for the set of the proposed composites. Taguchi technique reveals the optimum level factors for obtaining the minimum ‘WR’ is reinforcement content of 10 wt.%, applied load (P) at 10 N, sliding velocity (V) at 1 m s −1 and sliding distance (D) of 1000 m. The experiments results from DT algorithm, and analysis of variance and signal-to-noise ratio analysis from Taguchi-based approach confirmed that reinforcement is the primary element for affecting wear of the composites. The reason for applying DT algorithm is that, the low-level knowledge could be converted into high-level knowledge (If-then-else rules), which can be effortlessly explicable by semiskilled personnel.
The wear characteristics of Aluminium AA 5083/SiC/Fly Ash functional composites under different load conditions are an important aspect to assess the inoculation of Fly Ash for enhancing the functionality of the aluminium composites with respect to its tribological behaviour and its influence on wear properties. The present work is majorly aimed at the development of AA 5083/SiC functional composites inoculated with Fly Ash using stir casting method for different blends of the reinforcements (2.5, 5 & 7.5 wt%). The novelty of this research is majorly attributed to the incorporation of functional inoculants in the form of Fly Ash, which along with the SiC is bound to influence the tribological characteristics of the composites. The wear characteristics of these fabricated composites have been investigated considering various process parameters viz., the load, sliding distance, sliding velocity, wt% of SiC and wt% of Fly Ash, based on the operational requirements of the composites in real time considered from the earlier research studies and the influence of each parameter on the wear rate is discussed. Based on the different wear regimes obtained after characterization of the samples at different load conditions, Analysis of Variance (ANOVA) is carried out for each blend of the samples to statistically validate the experimental outcomes. The results have given sufficient substantiation to the fact that wear rate decreases with the inoculation. The wear rate and coefficient of friction (COF) is minimum viz., 0.00095 mm3/m, and 0.301 respectively for L9 experimental trial, i.e., for the composite specimens synthesized by reinforcing 7.5 wt% SiC, and 7.5 wt% Fly Ash for a load of 20 N, sliding velocity of 6 m s−1, and a sliding distance of 3000 m. The results have conferred that micro segregation (coring) of SiC and uniform dispersion of Fly Ash in the matrix enhances its tribological characteristics.
Waspaloy is one of the nickel-based alloys and its application is mostly positioned in the aerospace industry owing to its strength retaining capacity at higher temperature, better corrosion resistance, and toughness. Multi-response optimization technique, response surface methodology (RSM) was adopted to optimize the electrical discharge machining parameters during machining of Waspaloy. Various control factors such as peak current, voltage, duty cycle, and flushing pressure were selected with three levels. The material removal rate (MRR) and surface roughness (SR) were selected as response parameters for investigating the machining characteristics. A central composite design with five center points was used for experimental design. The best optimal set of control parameters were identified for the higher MRR and lower Sr The experiments have been validated by using analysis of variance and a confirmation test was conducted. From RSM, the optimum machining conditions for drilling the hole, namely, voltage: 125 V, flushing pressure: 0.8 kg cm −2 , and peak current: 22 A and duty cycle of 20% have been identified. Further, this investigation highlights the formation and the effect of the recast layer by using scanning electron microscopy.