This paper proposes a dynamic evolutionary model to quantify the domino effect of ship engine room fires. Based on the spatial and temporal characteristics of fire accidents, the dynamic probability of the domino effect of multiple accident units is calculated using matrix calculation and Monte Carlo simulation. The uncertainties of shipboard personnel, automatic detection systems, sprinkler systems, and the synergistic effects of multiple escalation vectors from different units are addressed. The dynamic probability of the domino effect of multiple accident units is calculated, and a risk assessment of complex fire scenarios in ship engine rooms is implemented. This study also presents the model feasibility in terms of fire risk assessment in cabins with numerous pieces of equipment. The results indicate that 2 min and 4 min are vital time nodes for the development and spread of fires. The extinguishing work on key equipment in the path of the fire's spread can effectively restrain its further expansion. The results can provide critical references for ship fire prevention, fire suppression, and fire protection design.

The box girder’s condition significantly impacts the safety and overall performance of the entire ship because it is the primary stress component of the hull construction. This work used experimental research on the long-span hull box girder based on IFEM (Inverse Finite Element Method) technology to ensure the structural safety of the hull box girder. Due to the limitations of conventional experiments in this technical field, such as their reliance on finite element data and lack of input from physical tests, numerous research methods combining the strain sensing data from physical tests with the strain data from virtual sensors were conducted. The strain fields of the top plate, side plate, and bottom plate were each reconstructed in turn, and the verifier measuring points in the physical model test were used to assess the accuracy of the reconstruction results. The findings demonstrate that the top plate, side plate, and bottom plate reconstructions had relative errors of 0.24–7.86%, 0.75–8.13%, and 3.31–2.52%, respectively. This enables the reconstruction of the strain field of the long-span hull box girder using physical test data and promotes the use of iFEM technology in the field of structural health monitoring of large marine structures.

Differing from previous studies on free-drop tests, this study focuses on the ultimate bearing capacity and failure mechanism of the ship’s bow under slamming loads. A prototype ship’s bow is selected to design two simplified stiffened plates with different stiffeners, and the lateral slamming loads used are equivalent to flare slamming loads. Free-drop tests of the two simplified models are conducted, and the test setups and procedures are provided. The experimental results of slamming pressures and structural responses are obtained. By comparing with the simulation results obtained by Arbitrary Lagrangian-Eulerian (ALE) fluid–structure coupling, the convergence study, symmetry, and independence verifications are carried out. Finally, the dynamic ultimate bearing capacity of stiffened plates with different stiffnesses under lateral slamming loads is studied. The results show that stiffeners enhance the ability of stiffened plates to resist plastic deformation under slamming loads, and T-section stiffeners can provide greater resistance to plastic deformation than other types.

The limit state function is important for the assessment of the longitudinal strength of damaged ships under combined bending moments in severe waves. As the limit state function cannot be obtained directly, the common approach is to calculate the results for the residual strength and approximate the limit state function by fitting, for which various methods have been proposed. In this study, four commonly used fitting methods are investigated: namely, the least-squares method, the moving least-squares method, the radial basis function neural network method, and the weighted piecewise fitting method. These fitting methods are adopted to fit the limit state functions of four typically sample distribution models as well as a damaged tanker and damaged bulk carrier. The residual strength of a damaged ship is obtained by an improved Smith method that accounts for the rotation of the neutral axis. Analysis of the results shows the accuracy of the linear least-squares method and nonlinear least-squares method, which are most commonly used by researchers, is relatively poor, while the weighted piecewise fitting method is the better choice for all investigated combined-bending conditions.

This study presents an integrated experimental and numerical investigation into the collapse characteristics of a cracked box girder subjected to bidirectional cyclic bending moments. An experimental test involving a box girder specimen with a prefabricated transverse crack on the deck panel is conducted under four-point bending to evaluate the influence of cracking on ultimate strength under cyclic loading. The findings are reported through load–displacement curves, strain measurements, and observations of both global and localised structural failure modes, demonstrating strong consistency with finite element simulations conducted using ABAQUS software (version 2022). The results reveal that cyclic loading prior to ultimate capacity induces negligible stiffness reduction in the box girder structure, consistent with the structural behaviour under monotonic loading. The initial failure mechanism is attributed to local buckling of the deck plate, subsequently followed by significant plastic deformation around the crack tips, ultimately leading to global collapse. Parametric studies are carried out to evaluate the influence of key variables on the girder’s residual strength, such as crack length, cyclic load amplitude and pattern.

In polar ship hull structural designs, methods based on regulations are considered the most authoritative; however, they tend to be conservative and often exhibit a notable degree of redundancy. This study aims to evaluate the applicability of the empirical formula for ice load assessments by conducting a series of quasi-static indentation tests on scaled hull plates under laboratory-made ice blocks of different scales. The obtained data include ice loads, structural responses, and characteristics of ice pressure distribution. A detailed comparison of various formulas is provided, along with an examination of their differences and errors in comparison to experimental results. The objective of this paper is to offer technical support for ice load forecasting and assessment.