Yufeng Zhang

Dr. Yufeng Zhang

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 March 2016 in Superconductor Science and Technology
Verified
Journal Article
Closed access
PDF file
YZYufeng Zhang
Yufeng Zhang
DZDifan Zhou
Difan Zhou
TITetsuya Ida
Tetsuya Ida
MMMotohiro Miki
Motohiro Miki
MIMitsuru Izumi
Mitsuru Izumi
The present manuscript addresses key issues in the course of our study of materials processing of bulk high-temperature superconductors, trapped flux and its application to a prototype axial-gap-type rotating machine. The TUMSAT group has conducted a series of studies since 2003 on the growth of GdBa 2 Cu 3 O 7− δ bulk material and its application in a compact low-speed high-torque rotating machine. In the stage of material growth, gaining the advantage of a large motive torque density requires large integrated flux in the motor/generators. A large grain surface might be required with sophisticated techniques for the melt-growth texture in the bulk with optimal flux pinning. In the second stage, the in situ magnetization procedure for bulk superconductors in the applied machine is a crucial part of the technology. Pulsed current excitation by using an armature copper winding has magnetized field pole bulks on the rotor. The axial-gap flux synchronous machine studied in the past decade is a condensed technology and indicates that further scientific development is required for a future compact machine to be superior to conventional ones in accordance with the cryogenic periphery and flux stabilization.

1 June 2010 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
YZYufeng Zhang
Yufeng Zhang
MIMitsuru Izumi
Mitsuru Izumi
YXY Xu
Y Xu
TGT Gao
T Gao
YKY Kimura
Y Kimura
By using a top seeding melt-textured growth process, single domain GdBa2Cu3O7−δ superconductor bulks with variable additions of oxide particles α-Fe2O3 were prepared in air. The effect of the α-Fe2O3 additions on the superconductivity properties was investigated. An increase of the critical current JC in low and moderate fields at 77 K was observed by adding tiny amounts of the α-Fe2O3 particles. The superconductor properties were not suppressed after the addition of the particles, with the superconducting transition temperature around 93.5 K. The present report showed that the α-Fe2O3 oxide particles may be embedded in the GdBa2Cu3O7−δ matrix to form the pinning center to enhance the critical current and the trapping field. With increasing α-Fe2O3 particles, however, the superconductor transition temperature shifts to 93 K and the critical current decreases.

25 February 2021 in Superconductor Science and Technology
Verified
Journal Article
Closed access
PDF file
JZJiaying Zhang
Jiaying Zhang
YZYufeng Zhang
Yufeng Zhang
ZLZiwei Lou
Ziwei Lou
PZPenghe Zhang
Penghe Zhang
CLChunyan Li
Chunyan Li
MIMitsuru Izumi
Mitsuru Izumi
Seven MgB 2 bulk superconductors with good superconductivity and crystallinity were prepared under the pressure of 50 MPa at 950 °C and different sintering durations (15 ∼ 240 min) by spark plasma sintering (SPS), with the onset critical temperature ( T c,onset ) around 37.5 K. The superconducting properties and microstructure measured from the facets perpendicular (PeF) and parallel (PaF) to the compression direction of the SPSed MgB 2 bulk samples were also analyzed to investigate the effect of the sintering duration on the MgB 2 bulks and the discrepancy between the PeF and the PaF. The optimum performance was obtained from the sample prepared for 45 min for both facets, and the critical current density ( J c ) measured from the PeF and the PaF are 364 kA cm −2 and 344 kA cm −2 in self field at 20 K, respectively. The PeF exhibits better J c performance than the PaF at low fields and the PaF exhibits better J c performance than the PeF at high fields. It can be concluded that the sintering duration affects the properties of the PeF mainly by changing their crystallite size. While for the PaF, the sintering duration mainly affects the microstructural defects, such as cracks, pores and secondary phase particles, thus further affecting their J c performances. In terms of the flux pinning mechanism of the SPSed MgB 2 bulk samples, the PaF is less susceptible to sintering duration than the PeF, and the better J c performance of the PaF at high fields is due to the stronger grain boundary pinning. It can be also found that the point pinning being stronger at higher temperature is the result of the decreasing anisotropy of MgB 2 bulk samples with the temperature.

30 April 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
PZPenghe Zhang
Penghe Zhang
YZYufeng Zhang
Yufeng Zhang
CLChunyan Li
Chunyan Li
YZYan Zhang
Yan Zhang
SSShuangyuan Shen
Shuangyuan Shen
JNJacques G. Noudem
Jacques G. Noudem
Two MgB2 samples were prepared using the spark plasma sintering (SPS) technique at different temperatures—950 °C (S1) and 975 °C (S2)—for 2 h under 50 MPa pressure to study the influence of preparation temperature on different facets, namely those perpendicular (PeF) and parallel (PaF) to the compression direction of uniaxial pressure during the SPS of MgB2 samples. We analyzed the superconducting properties of the PeF and PaF of two MgB2 samples prepared at different temperatures from the curves of the critical temperature (TC), the curves of critical current density (JC), the microstructures of MgB2 samples, and the crystal size from SEM. The values of the onset of the critical transition temperature, Tc,onset, were around 37.5 K and the transition widths were about 1 K, which indicates that the two samples exhibit good crystallinity and homogeneity. The PeF of the SPSed samples exhibited slightly higher JC compared with that of the PaF of the SPSed samples over the whole magnetic field. The values of the pinning force related to parameters h0 and Kn of the PeF were lower than those of the PaF, except for Kn of the PeF of S1, which means that the PeF has a stronger GBP than the PaF. In low field, the most outstanding performance was S1-PeF, whose critical current density (JC) was 503 kA/cm2 self-field at 10 K, and its crystal size was the smallest (0.24 µm) among all the tested samples, which is consistent with the theory that a smaller crystal size can improve the JC of MgB2. However, in high field, S2-PeF had the highest JC value, which is related to the pinning mechanism and can be explained by grain boundary pinning (GBP). With an increase in preparation temperature, S2 showed a slightly stronger anisotropy of properties. In addition, with an increase in temperature, point pinning becomes stronger to form effective pinning centers, leading to a higher JC.

29 April 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
YZYufeng Zhang
Yufeng Zhang
ZLZiwei Lou
Ziwei Lou
PZPenghe Zhang
Penghe Zhang
CLChunyan Li
Chunyan Li
JZJiaying Zhang
Jiaying Zhang
XZXiaojuan Zhang
Xiaojuan Zhang
The performance of critical current density of GdBa2Cu3O7−δ (GdBCO or Gd123) superconductor bulk has an important influence on its practical applications. In this work, four single-domain GdBCO superconductor bulks were successfully processed by the modified top-seeded melt-texture growth method. The addition of a YBa2Cu3O7−δ (Y123) liquid source with different thicknesses, 0 mm (S0), 3 mm (S3), 5 mm (S5), 7 mm (S7), was introduced to study the influence on the superconducting properties. GdBCO bulk with the addition of the Y123 liquid source with a 3-mm thickness shows the best superconducting properties. The addition of the Y123 liquid source results in a decrease in the Gd3+ ion concentration required for Gd123 growth; thus, Gd2BaCuO5 (Gd211) particles in the liquid source need a larger self-decomposition to diffuse Gd3+ ions to Gd123 growth front, which refines the size and leads to a homogenous distribution of the Gd211 particles in the bulks. Thus, the more pinning centers of fined Gd211 particles improve the superconducting properties of GdBCO bulk. With increases in the thickness of Y123 liquid source to 5 mm and 7 mm, high RE3+ (Gd3+ and Y3+) concentration can coarsen Gd211 particles and fuse with Gd211 liquid source. The superconducting properties apparently drop. Therefore, the addition of a Y123 liquid source with a suitable thickness is a positive modification to obtain high-performance GdBCO bulk.

2 July 2025 in The Journal of Chemical Physics
Verified
Journal Article
Closed access
JJJiajun Jiang
Jiajun Jiang
YXYamin Xue
Yamin Xue
ZXZehui Xiong
Zehui Xiong
SYShunwei Yao
Shunwei Yao
ZCZebang Cheng
Zebang Cheng
Jia LinJia Lin
Jia Lin
In the field of hydride superconductors, a great challenge is to achieve superconducting states under ambient pressure conditions rather than the extreme high-pressure environments that have been required in experiments. Achieving this goal is crucial for advancing the practical applications of high-temperature superconducting materials. We discover a family of compounds (hydride double perovskite superconductors with space group Fm3̄m and chemical formula A2MM′H6) to achieves this goal. A machine-learning-accelerated approach is utilized to search for hydride double perovskite superconductors under ambient pressure within an extensive dataset comprising over 106 535 hypothetical compounds. 15 stable hydride double perovskite superconductors are discovered under ambient pressure, with the highest superconducting transition temperature (Tc) reaching 18.7 K. The structural stability, electronic properties, and superconducting behavior of these materials have been comprehensively analyzed. Phonon dispersion analysis has highlighted the critical role of lattice vibrations in electron–phonon coupling (EPC), where the contribution of H atom vibrations is essential for facilitating electron pairing and the onset of superconductivity. This demonstrates that the machine-learning-accelerated approach is a highly effective method and can be easily extended to other compounds.