Chalcogenide perovskites exhibit optoelectronic properties that position them as potential materials in the field of photovoltaics. We report a detailed investigation into the electronic structure and chemical properties of polycrystalline BaZrS3 perovskite powder by X-ray photoelectron spectroscopy, complemented by an analysis of its long- and short-range geometric structures using X-ray diffraction and X-ray absorption spectroscopy. The results obtained for the powdered BaZrS3 are compared to similar measurements on a sputtered polycrystalline BaZrS3 thin film prepared through rapid thermal processing. While bulk characterization confirms the good quality of the powder, depth-profiling achieved by photoelectron spectroscopy utilizing Al Kα (1.487 keV) and Ga Kα (9.25 keV) radiations shows that, regardless of the fabrication method, the oxidation effects extend beyond 10 nm from the sample surface, with zirconium oxides specifically distributing deeper than the oxidized sulfur species. A hard X-ray photoelectron spectroscopy study on the powder and thin film detects signals with minimal contamination contributions and allows for the determination of the valence band maximum position with respect to the Fermi level. Based on these measurements, we establish a correlation between the experimental valence band spectra and the theoretical density of states derived from density functional theory calculations, thereby discerning the orbital constituents involved. Our analysis provides an improved understanding of the electronic structure of BaZrS3 developed through different synthesis protocols by linking it to material geometry, surface chemistry, and the nature of doping. This methodology can thus be adapted for describing electronic structures of chalcogenide perovskite semiconductors in general, a knowledge that is significant for interface engineering and, consequently, for device integration.
Exploring the conduction mechanism in the chalcogenide perovskite Ba Zr S 3 is of significant interest due to its potential suitability as a top absorber layer in silicon-based tandem solar cells and other optoelectronic applications. Theoretical and experimental studies anticipate native ambipolar doping in Ba Zr S 3 , although experimental validation remains limited. This study reveals a transition from highly insulating behavior to n -type conductivity (approximately 100 S/cm) in Ba Zr S 3 thin films through annealing in an S -poor environment. Ba Zr S 3 thin films are synthesized via a two-step process: co-sputtering of Ba - Zr followed by sulfurization at 600 ∘ C , and subsequent annealing in high vacuum. Ultraviolet-visible spectroscopy measurements reveal a red shift of approximately 100 meV in the band gap concurrent with sample-color darkening after vacuum annealing. The increase in defect density from the order of 10 17 to 10 21 cm − 3 with vacuum annealing, coupled with the low activation energy (approximately 8 meV), and the n -type character of the defects, strongly suggests that sulfur vacancies ( V S ) are responsible for the n -type doping, in agreement with theoretical predictions. Temperature-dependent Hall measurement shows that phonon scattering governs charge transport at room temperature in Ba Zr S 3 films and that S vacancies are shallow donor defects acting as a weak impurity metal. The shift of the valence-band maximum (VBM) with respect to the Fermi level, quantified by hard x-ray photoelectron spectroscopy ( Ga K α , 9.25 keV), further corroborates the induced n type of conductivity in annealed samples. Our findings indicate that vacuum annealing induces V S defects that dominate charge transport, resulting in n -type conductivity in Ba Zr S 3 under S -poor conditions. These discoveries will inform important design choices, such as selecting appropriate contact materials, for integrating Ba Zr S 3 into solar cell structures or other devices.
To commercialize lead halide perovskites as light-emitting diodes (LEDs), the operational device lifetime needs to be drastically improved. For this to be achieved, an understanding of degradation behavior under bias is crucial. Herein, we perform operando measurements of the structural, chemical, and electronic changes using synchrotron-based grazing-incidence wide-angle X-ray scattering and hard X-ray photoelectron spectroscopy on full-stack deep blue mixed bromide/chloride lead halide perovskite LEDs. While a clear drop in optoelectronic performance is recorded under electrical bias, the accompanying X-ray scattering data reveals only minor changes in structural properties. However, photoelectron spectroscopy reveals substantial chemical changes at the electron-injecting interface after bias is applied, including the formation of unwanted metallic lead and a new chlorine species that is not in the perovskite structure. These operando approaches give important structural and interfacial perspectives to reveal the degradation mechanisms in these LEDs and highlight the need to address the top electron-injecting interface to realize step-changes in operational stability.
Lead halide perovskites have been revolutionary in the last decade in many optoelectronic sectors. Their bismuth-based counterparts have been considered a good alternative thanks to their composition of earth-abundant elements, good chemical stability, and low toxicity. Moreover, their electronic structure is in a quasi-zero-dimensional (0D) configuration, and they have recently been explored for use beyond optoelectronics. A significant limitation in applying thin-film technology is represented by the difficulty of synthesizing compact layers with easily scalable methods. Here, the engineering of a two-step synthesis in an air of methylammonium bismuth iodide compact thin films is reported. The critical steps of the process have been highlighted so that the procedure can be adapted to different substrates and application areas.