The prompt fission -ray energy spectrum for cold-neutron-induced fission of was measured in the energy range , by gaining a factor of about in statistics compared to the measurements performed so far. The spectrum exhibits local bump structures at and , and also a broad one at . In order to understand the origins of these bumps, the spectra were calculated using a statistical Hauser-Feshbach model, taking into account the deexcitation of all the possible primary fission fragments. It is shown that the bump at is created by the transitions between the discrete levels in the fragments around , and the bump at mostly comes from the complementary light fragments. It is also indicated that a limited number of nuclides, which have high-spin states at low excitation energies, can contribute to the bump structure around , induced by the transition feeding into the low-lying high-spin states.
Exploring the conduction mechanism in the chalcogenide perovskite Ba Zr S 3 is of significant interest due to its potential suitability as a top absorber layer in silicon-based tandem solar cells and other optoelectronic applications. Theoretical and experimental studies anticipate native ambipolar doping in Ba Zr S 3 , although experimental validation remains limited. This study reveals a transition from highly insulating behavior to n -type conductivity (approximately 100 S/cm) in Ba Zr S 3 thin films through annealing in an S -poor environment. Ba Zr S 3 thin films are synthesized via a two-step process: co-sputtering of Ba - Zr followed by sulfurization at 600 ∘ C , and subsequent annealing in high vacuum. Ultraviolet-visible spectroscopy measurements reveal a red shift of approximately 100 meV in the band gap concurrent with sample-color darkening after vacuum annealing. The increase in defect density from the order of 10 17 to 10 21 cm − 3 with vacuum annealing, coupled with the low activation energy (approximately 8 meV), and the n -type character of the defects, strongly suggests that sulfur vacancies ( V S ) are responsible for the n -type doping, in agreement with theoretical predictions. Temperature-dependent Hall measurement shows that phonon scattering governs charge transport at room temperature in Ba Zr S 3 films and that S vacancies are shallow donor defects acting as a weak impurity metal. The shift of the valence-band maximum (VBM) with respect to the Fermi level, quantified by hard x-ray photoelectron spectroscopy ( Ga K α , 9.25 keV), further corroborates the induced n type of conductivity in annealed samples. Our findings indicate that vacuum annealing induces V S defects that dominate charge transport, resulting in n -type conductivity in Ba Zr S 3 under S -poor conditions. These discoveries will inform important design choices, such as selecting appropriate contact materials, for integrating Ba Zr S 3 into solar cell structures or other devices.
BaZrS3 stands out as one of the most extensively researched chalcogenide perovskites. Unlike its halide counterpart, this Pb-free alternative boasts superior intrinsic chemical stability. Notably, all three chemical elements are among the 20 most abundant elements in Earth's crust. With a band gap of approximately 1.8 eV, it is theoretically well suited to augment Si in tandem cells. Additionally, BaZrS3 exhibits one of the highest band-edge absorption levels among all known solar cell materials and maintains stability in air up to 400 °C. However, the synthesis of BaZrS3 thin films—essential for typical optoelectronic devices—remains a challenge. The primary obstacle lies in the elevated process temperatures required for achieving a high degree of crystallinity, potentially hindering integration into tandem photovoltaic devices. Nonetheless, the formation of high-order Ba polysulfides as intermediate phases can notably decrease the growth temperature of BaZrS3. The purpose of the present work is to produce a pressure-temperature phase diagram for the Ba–S system, defining the domains of stability of binary Ba sulfides. By independently varying the temperatures of the sample and the S vapor source, an experimental phase diagram is initially constructed. Then a first-principles thermodynamic model for the sulfurisation of Ba is built and the theoretical results are compared with the experimental results. Good agreement is found for the BaS2–BaS3 transition, while the discrepancy observed for the BaS2–BaS transition is attributed to equipment limitations. In the process, the easily overlooked roles of thermal gradients and thermal transport in the flow reactor are also highlighted. The insights gleaned are relevant to general thin-film sulfurisation systems, where achieving and maintaining a controlled high partial vapor pressure of S present greater challenges compared to solid-state chemistry. This study offers valuable thermodynamic guidance for the synthesis of a wide range of Ba sulfides and is of particular relevance for the formation of BaZrS3 perovskites at moderate temperature.
21 June 2024 in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
The Applied Nuclear Physics Group at Lund University has constructed a CANS (Compact Accelerator-driven Neutron Source). The CANS is based around a 3 MV, single-ended, Pelletron accelerator, which is used to impinge a 2.8 MeV deuterium beam into a beryllium target. The anticipated neutron production will be on the order of 1010 n/s in 4π sr, with future upgrades expected to increase neutron production to 1011 n/s. Neutron energy will be up to 9 MeV with peak emission at ∼5 MeV. Shielding and moderation will be provided by a large water tank surrounding the target, with exit ports to allow moderated neutrons to be directed to experiments. The thermal-neutron flux at the exit of the extraction ports is anticipated to be up to 106 n/cm2/s. The CANS will be used to forward the activities of the group in the area of neutron-activation analysis, in addition to a broader range of neutron related applications.
29 May 2024 in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms