This paper compared the effects of A. indica plant proteins over chemical methods in the morphology of zinc oxide nanoparticles (ZnO NPs) prepared by a co-precipitation method, and ethanol sensing performance of prepared thin films deposited over a fluorene-doped tin oxide (FTO) bind glass substrate using spray pyrolysis technique. The average crystallite sizes and diameters of the grain-sized cluster ZnO NPs were 25 and (701.79 ± 176.21) nm for an undoped sample and 20 and (489.99 ± 112.96) nm for A. india dye-doped sample. The fourier transform infrared spectroscopy (FTIR) analysis confirmed the formation of the Zn–O bond at 450 cm⁻¹, and also showed the presence of plant proteins due to A. indica dye extracts. ZnO NPs films exhibited good response (up to 51 and 72% for without and with A. indica dye-doped extracts, respectively) toward ethanol vapors with quick response-recovery characteristics at a temperature of 250 °C for undoped and 225 °C for A. indica dye-doped ZnO thin films. The interaction of A. indica dye extracts helps to decrease the operating temperature and increased the response and recovery rates of the sensor, which may be due to an increase in the specific surface area, resulting in adsorption of more oxygen and hence high response results.

The physical phenomena of convective flow of Cross fluid containing carboxymethyl cellulose water over a stretching sheet with convective heating were studied. Cross nanofluid containing Al₂O₃, Cu nanoparticles, and based fluid of CMC water is used. Entropy generation minimization is examined in the current analysis. The system of PDEs is altered into a set of ODEs through suitable conversion. Further, these equations are computed numerically through the MATLAB BVP4c technique. The behavior of governing parameters on the velocity, temperature, entropy generation, and Bejan number is plotted and reported via graphs. It is found that the larger value of unsteady variable reduced the velocity, thermal layer, and entropy production. Surface drag frication of the Al₂O₃ and Cu and Al₂O₃ + Cu is enhanced with the more presence of unsteady parameter. Comparison of current results in a limiting case is obtained with earlier analysis and found an optimum agreement.

The consequence of periodic body acceleration and thermal radiation in the pulsating flow of MHD Casson nanofluid through a porous channel is addressed. A flow of the nanofluid injected through the lower plate is considered while sucked out through the upper plate with a similar velocity. The thermal radiation term is incorporated in the heat transfer equation. The governing equations corresponding to velocity and temperature are converted from partial differential equations to a system of ordinary differential equations by employing similarity variables. The perturbation technique is applied to solve the governing flow equations. The impact of diverse parameters on flow features is graphically analyzed. The result reveals that adding the nanoparticle has enhanced the velocity profile of the base fluid. Moreover, an increase in the periodic body acceleration results in enlarging velocity and temperature.

In this exploration, we decided to investigate the significance of prescribed thermal conditions on unsteady 3D dynamics of water‐based radiative hybrid nanofluid with the impact of cylindrical‐shaped nanosized particles (alumina (Al₂O₃) and titania (TiO₂)). For physical relevancy, the impact of the Lorentz force is also included. The combination of suitable variables has been used to transform the transport equations into the system of ordinary differential equations and then numerically solved via the Keller‐Box approach. Graphical illustrations have been used to predict the impact of the involved parameters on the thermal setup. Convergence analysis is presented via the grid independence approach. Skin frictions and local Nusselt numbers against various choices of involved parameters are plotted and arranged in tabular forms. It is observed through the present investigation that temperature distribution is increased with the higher choices of radiation parameter 0.0 ≤ R_d ≤ 2.0 and decreased with the improvement in the choices of temperature maintaining indices (i.e., −2.0 ≤ r, s ≤ 2.0). Moreover, the thermophysical properties except specific heat for hybrid nanofluid are improved with the involvement of cylindrical‐shaped nanoparticles. The temperature of the hybrid nanofluid is observed to be higher for variable thermal conditions as compared to uniform thermal conditions. Outfalls for a limited version of the report have been compared with a previous published paper.