Mat foundations are most typically used in locations featuring weak soils such as soft clays and silts, particularly when building in demanding geotechnical conditions. Because of their poor engineering characteristics and significant difficulties associated with workability, these soils are often removed or avoided by excavating down to a specific depth. However, if thick layers are present, their removal becomes unpractical, costly, and creates inconvenience during construction. To overcome this issue, various reinforcement strategies can be adopted. In this study, the use of stone columns under mat foundations was investigated via numerical modeling. Two scenarios were compared: one in which stone columns were installed without any soil removal and another in which a layer of soft ground was removed and the foundation was installed without any ground treatment. Numerical results showed the clear beneficial effect of stone columns, which can significantly reduce settlements even in the presence of a thick deformable soil layer.
Solid waste management is a major environmental challenge, especially in developing countries, with increasing amounts of waste glass (WG) and waste plastic (WP) not being recycled. In Ethiopia, managing WG and WP requires innovative recycling techniques. This study examines concrete properties with WG and WP as partial replacements for fine aggregate. Tests were conducted on cement setting time, workability, compressive strength, splitting tensile strength, and flexural strength. Concrete of grade C-25, with a target compressive strength of 25 MPa, was prepared by partially replacing fine aggregate with WP and WG. The mechanical properties were evaluated after 7 and 28 days of curing. At a 20% replacement level, workability decreased at water–cement ratios of 0.5 and 0.6 but remained stable at 0.4, leading to the selection of the 0.4 ratio for further testing. A 10% replacement of fine aggregate, using a ratio of 3% WP and 7% WG, was found to be optimal, resulting in an increase in compressive strength by 12.55% and 6.44% at 7 and 28 days, respectively. In contrast, a 20% replacement led to a decrease in compressive strength by 14.35% and 0.73% at 7 and 28 days, respectively. On the 28th day, the splitting tensile strength at the optimal replacement level was 4.3 MPa, reflecting an 8.5% reduction compared to the control mix. However, flexural strength improved significantly by 19.7%, from 12.46 MPa to 15.52 MPa. Overall, the incorporation of WG and WP in concrete enhances flexural strength but slightly reduces splitting tensile strength.
The California bearing ratio (CBR) is a key parameter for flexible pavement and airfield runway design; however, its laboratory determination is labor‐intensive, time‐consuming, and costly. This study developed a predictive model for soaked CBR values using compaction characteristics and some index properties of soil to provide a cost‐effective estimation tool for subgrade soils in Seka Town, Ethiopia. A total of 39 fine‐grained soil samples were collected from an ongoing roadway construction project. Thirty samples were used for model calibration, while the remaining nine samples were reserved for internal validation. Laboratory testing was conducted in accordance with ASTM and American Association of State Highway and Transportation Officials (AASHTO) standards to determine index properties, including percentage passing sieve No. 200, liquid limit (LL), plastic limit (PL), and plasticity index (PI) as well as compaction characteristics such as maximum dry density (MDD) and optimum moisture content (OMC) and CBR values. The investigated soils were predominantly classified as MH and ML under the Unified Soil Classification System (USCS) and A‐7‐5 and A‐7‐6 under the AASHTO classification system. Simple and multiple linear regression (MLR) analyses were performed using SPSS software. Among the developed models, the MLR equation, CBR = −12.124 − 0.077LL − 0.178OMC + 20.37MDD, demonstrated a strong correlation (adjusted R2 = 0.887) and the best predictive performance with low error metrics (MAE = 0.511, MAPE = 6.84%, and RMSE = 0.66). Internal validation confirmed good predictive accuracy, with an average variation of 3.64%. However, external validation using a secondary dataset resulted in a significant average variation with a low correlation ( R2 = 0.381) and relatively high error metrics (MAE = 4.471, MAPE = 43.65% and RMSE = 4.76), indicating poor generalizability across different geographic regions. Therefore, the developed model should be considered preliminary and locally applicable to soils with characteristics similar to those of the study area. Further validation using larger, multiregion datasets and advanced modeling approaches is recommended before broader practical engineering application.
Solid waste management is a major environmental challenge, especially in developing countries, with increasing amounts of waste glass (WG) and waste plastics (WP) not being recycled. In Ethiopia, managing WG and WP requires innovative recycling techniques. This study examines concrete properties with WG and WP as partial replacements for fine aggregate. Tests were conducted on cement setting time, workability, compressive strength, splitting tensile strength, and flexural strength. Concrete grade C-25, with a compressive strength of 25 MPa, was prepared using an optimum ratio of 14% WG and 6% WP. Mechanical properties were tested at 7 and 28 days of curing. At 20% replacement, workability decreased at water-cement ratios of 0.5 and 0.6 but remained stable at 0.4. Thus, a 0.4 ratio was used. For 10% replacement, compressive strength increased by 12.55% and 6.44% on the 7th and 28th days, respectively. At 20% replacement, compressive strength decreased by 14.35% and 0.73% on the 7th and 28th days, respectively. On the 28th day, splitting tensile strength at optimum replacement was 4.3 MPa, an 8.5% reduction from the control mix. However, flexural strength increased by 19.7%, from 12.46 MPa to 15.52 MPa. Overall, WG and WP improved flexural strength but slightly reduced splitting tensile strength.
There are various modeling techniques adopted for predicting the labor productivity that incorporate the influence of various factors, but neural networks are found to have strong pattern recognition and higher accuracy to get reliable estimates. To develop a construction labor productivity (CLP) model for concreting activities, data were collected through a questionnaire. The most critical influencing parameters were ranked according to their relative importance index (RII). Then the strength of the relationship between CLP and influencing parameters was analyzed using correlation coefficient results generated in Python program. Finally, the CLP model which represents the output of the crew within a certain factor was successfully developed using artificial neural networks (ANNs). Five objectives and six subjective critical influencing parameters were selected using RII. Crew experience, age of workers, and placement technique are the top three influencing parameters that have a strong relation with CLP with correlation coefficient values of 0.5681, 0.5349, and 0.5227 respectively. The developed model within these influencing parameters has a higher capability to predict the output of labor with a 92% coefficient of determination (R2) and a mean squared error of 0.316%. Therefore, the application of such a model for the accurate estimation of labor productivity is recommended.