Alemu M Legese

Dr. Alemu M Legese

Civil, Construction, and Environmental Engineering, University of Delaware, Newark, California, USA
+2
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 February 2023 in Construction Materials
Verified
Journal Article
Open access
PDF file
MMMuniter Muresa
Muniter Muresa
Alemu M LegeseAlemu M Legese
Alemu M Legese
GUGirum Urgessa
Girum Urgessa
TBTeshome Boja
Teshome Boja
Due to expansion in infrastructure and increased development of urbanization in Ethiopia, most of the places are covered either by impermeable cement concrete or bitumen that blocks the percolation of water from rainfall. A porous concrete made of zero fine aggregates, creating a pore that permits the concrete to be water permeable, is highly desirable. Similarly, the demand for natural coarse aggregates remains high, while natural resources are being depleted. Therefore, this study aims to investigate the properties of porous concrete using recycled concrete aggregate as a partial replacement for natural coarse aggregate. Experimental tests were conducted on cement setting time, workability of concrete, compressive, split tensile, porosity, and permeability of porous concrete. The properties of porous concrete at different ratios—0, 15, 30, 45 and 60%—revealed that RCA is suitable for use as coarse aggregate. The optimum replacement percentage of recycled aggregate for porous concrete in terms of strength is 30%, with 28th-day compressive strength of 17.37 MPa. However, slight increments were observed in porosity and permeability coefficient. Therefore, the concrete produced in this study is structural concrete, which is suitable for walkways and other concrete flat works, whereby heavy vehicle traffic loads do not exist.

5 January 2017 in American Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
ETEshetu Tsega
Eshetu Tsega
Alemu M LegeseAlemu M Legese
Alemu M Legese
FFFekadu Fufa
Fekadu Fufa
Brick is one of the most widely used conventional construction materials throughout the world. The production cost of clay brick is significantly affected by the cost of energy required for firing. The aim of this research is to investigate the effects of different firing temperatures on the compressive strength (CS), water absorption (WA) and saturation coefficients (SC) of fired clay bricks produced around Jimma Town and evaluate the effect of firing processes in brick manufacturing on the properties, color and appearance of the clay brick. During the production process, the effects of different heating rates on physical and mechanical properties of firing standard bricks were analyzed. In this study, different heating rates were used: slow heating rate and fast heating rate. Changes in the physical and mechanical properties of the fired clay brick were assessed with the increase in the firing temperature firing time. The results show that the CS increased with the increase in the firing temperature. On the contrary, WA and SC of the fired clay bricks decreased with the increase in the firing temperature. Increment in the duration of firing slightly increases the CS and lowers both the WA and WA of the clay brick. In the study area, traditional brick producers did not have firing temperature control device or mechanism in the fired clay brick production. The kiln operator decided the firing temperature and duration. The absence of the device frequently results in the over or under firing of bricks greatly affecting the engineering properties of this widely used contraction material. Therefore, the traditional clay brick producers should install the temperature control device on their kiln or at least needs to be trained how to approximately determine the optimum temperature.

1 January 2020 in American Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
GEGemeda Etefa
Gemeda Etefa
Alemu M LegeseAlemu M Legese
Alemu M Legese
Concrete tile is one of the most used construction materials in the world. Cement and aggregate, which are the most important constituents used in concrete tile production, they are the vital materials needed for the construction industry. This led to a continuous and increasing demand of natural materials used for their production. Parallel to the need for the utilization of the natural resources emerges a growing concern for protecting the environment and a need to preserve natural resources (such as aggregate) by using alternative materials which are recycled or waste materials. In this research, a study was carried out on the use of used rubber tires as a partial replacement for coarse aggregates in concrete tile production using locally available waste tires. A review of relevant literatures was done to study previous works in the subject matter. The research was carried out by conducting tests on the raw materials to determine their properties and suitability for the experiment. Concrete mix designs are prepared using the DOE method and a total of 12 mixes were prepared consisting of two concrete grades (C25 and C30). The specimens were produced with percentage replacements of the coarse aggregate by 10, 20, 30, 40 and 50% of rubber aggregate with and without supper plasticizer (admixture). Moreover, a control mix with no replacement of the coarse aggregate was produced to make a comparative analysis. The prepared samples consist of concrete cubes, cylinders and beams. Laboratory tests were carried out on the prepared concrete samples. The lists of tests conducted are; material property, slump, unit weight, compressive strength, splitting tensile strength and flexural strength tests. The data collection was mainly based on the tests conducted on the prepared specimens in the laboratory. The test results were compared with the respective conventional concrete properties and show that there is a reduction in compressive strength of the concrete due to the inclusion of rubber aggregates. This is improved by using admixture to some extent, but lower density and enhanced ductility are the same, and there was a slight increase in flexural strength without admixture. The overall results show that it is possible to use recycled rubber tires in concrete tile production as a partial replacement for coarse aggregates. Nevertheless, the percentage of replacement should be limited to 10%.

1 June 2021 in Studia Geotechnica et Mechanica
Verified
Journal Article
Open access
Alemu M LegeseAlemu M Legese
Alemu M Legese
TKTesfaye Geneti Kenate
Tesfaye Geneti Kenate
FFFekadu Fufa Feyessa
Fekadu Fufa Feyessa
The article presents the alternative use of termite mound soils (TMSs) as full replacement for clay soils in brick production. TMSs from two localities, Jawaj and Sene, in Ethiopia were investigated for bricks production. The TMSs samples contained high SiO2 and Al2O3. The TMSs bricks were fired at different temperatures from 500 to 1,000°C. The obtained mean compressive strengths (σ), 18 and 14 MPa, were observed for bricks made from TMSs from Jawaj and Sene, respectively, at the optimum firing temperature of 700°C. The σ of TMSs bricks decreased as the firing temperature increased above 700°C, while for conventional clay soil brick, the σ increased with temperature beyond 700°C. The water absorptions and saturation coefficients of fired TMSs bricks decreased with increased firing temperature. The TMSs bricks meet the standard specification of dimension tolerance only along the height. All the TMSs bricks made from the two localities were not efflorescent. TMSs from Jawaj and Sene sites can be used as a raw material to replace the long-used clay soils for bricks production as a construction material for houses construction in rural and urban areas.

9 March 2023 in Studia Geotechnica et Mechanica
Verified
Journal Article
Open access
PDF file
HGHaile Tsegay Gebresamuel
Haile Tsegay Gebresamuel
DMDamtew Tsige Melese
Damtew Tsige Melese
YBYada Tesfaye Boru
Yada Tesfaye Boru
Alemu M LegeseAlemu M Legese
Alemu M Legese
The undrained shear strength (Su) and cohesion (Cu) of cohesive soils are frequently determined using an unconfined compression test. However, the test results are heavily dependent on specimen size. This causes uncertainty in geotechnical analyses, constitutive models, and designs by overestimating or underestimating the shear strength of cohesive soils. Therefore, the study aims to assess the effect of the height-to-diameter ratio on the unconfined compressive strength (UCS) of cohesive soil. The soil specimen was tested on a compacted cylindrical specimen at the maximum dry density and optimum moisture content with a height to diameter (H/D) ratio of 1–3 for 38, 50, and 100 mm specimen diameters. Disturbed sample specimens were considered for the laboratory program. Accordingly, the standard Proctor compaction test determines soil classification and compaction characteristics. The unconfined compression test was performed for undisturbed and compacted remolded states of various diameters of cohesive soil specimens to investigate the strength variation with the specimen variation in H/D ratio. The laboratory test results revealed that cohesive soil's unconfined compression strength value drops rapidly with height-to-diameter ratios and the soil specimens’ diameter increases. However, the UCS value was stable at H/D ratio from 1.75 to 2.25. As the specimens’ diameter and H/D ratio increased, the peak UCS value axial strain decreased. Similarly, the gap between the axial strains of peak UCS value for the smallest and the most significant H/D ratio decreased with increase in the specimens’ diameter.

4 September 2024 in Construction Materials
Verified
Journal Article
Open access
PDF file
Alemu M LegeseAlemu M Legese
Alemu M Legese
DMDegefe Mitiku
Degefe Mitiku
FFFekadu Feyessa Fufa
Fekadu Feyessa Fufa
GUGirum Urgessa
Girum Urgessa
YBYada Tesfaye Boru
Yada Tesfaye Boru
Solid waste management is a major environmental challenge, especially in developing countries, with increasing amounts of waste glass (WG) and waste plastic (WP) not being recycled. In Ethiopia, managing WG and WP requires innovative recycling techniques. This study examines concrete properties with WG and WP as partial replacements for fine aggregate. Tests were conducted on cement setting time, workability, compressive strength, splitting tensile strength, and flexural strength. Concrete of grade C-25, with a target compressive strength of 25 MPa, was prepared by partially replacing fine aggregate with WP and WG. The mechanical properties were evaluated after 7 and 28 days of curing. At a 20% replacement level, workability decreased at water–cement ratios of 0.5 and 0.6 but remained stable at 0.4, leading to the selection of the 0.4 ratio for further testing. A 10% replacement of fine aggregate, using a ratio of 3% WP and 7% WG, was found to be optimal, resulting in an increase in compressive strength by 12.55% and 6.44% at 7 and 28 days, respectively. In contrast, a 20% replacement led to a decrease in compressive strength by 14.35% and 0.73% at 7 and 28 days, respectively. On the 28th day, the splitting tensile strength at the optimal replacement level was 4.3 MPa, reflecting an 8.5% reduction compared to the control mix. However, flexural strength improved significantly by 19.7%, from 12.46 MPa to 15.52 MPa. Overall, the incorporation of WG and WP in concrete enhances flexural strength but slightly reduces splitting tensile strength.