More than 90% of the natural gas hydrate resources are reserved as marine clayey silt sediments. It is of great significance to efficiently develop a clayey silt hydrate. At present, there are problems of low single well production and small depressurization range in its production test, which is still a long way from commercial exploitation. The combination of hydraulic fracturing technology and other methods such as depressurization method is regarded as one of the potential technical means to achieve the commercial exploitation of the hydrate. However, compared with shale gas reservoirs and coalbed methane reservoirs, clayey silt hydrate reservoirs have special mechanical properties, resulting in unique hydraulic fracturing processes. Therefore, it is necessary to study the fracture initiation and propagation laws of clayey silt hydrate reservoirs. To this end, we carried out large-scale (30 × 30 × 30 cm) true triaxial hydraulic fracturing experiments using a simulated material with similar mechanics, porosity, and permeability to clayey silt hydrate-bearing sediments. The effects of completion method, fracturing method, and fracturing fluid displacement on hydraulic fracture propagation of clayey silt hydrate-bearing sediments were studied. The results showed that a perforated completion can significantly increase the fracture reconstruction area and decrease the fracture initiation pressure compared to an open hole completion. Due to the small horizontal stress difference, it is feasible to carry out temporary plugging fracturing in clayey silt hydrate reservoirs. Temporary plugging fracturing can form steering fractures and significantly improve fracture complexity and fracture area. Increasing the fracturing fluid displacement can significantly increase the fracture area as well. When conducting fracturing in clayey silt hydrate-bearing sediments, the fracturing fluid filtration area is obviously larger than the fracture propagation area. Therefore, it is recommended to use a high-viscosity fracturing fluid to reduce the filtration of the fracturing fluid and improve the fracturing fluid efficiency. This study preliminarily explores the feasibility of temporary plugging fracturing in clayey silt hydrate reservoirs and analyzes the effect of completion methods on the propagation of fracturing fractures, which can provide a reference for the research conducted on the fracturing stimulation of clayey silt hydrate reservoirs.

The cement sheath is critical for ensuring the long-term safety and operational efficiency of oil and gas wells. However, complex geological conditions and operational stresses during production can induce cement sheath deterioration and cracking, leading to reduced zonal isolation, diminished hydrocarbon recovery, and elevated operational expenditures. This study investigates the development of a novel microbial self-healing well cement slurry system, employing fly ash as microbial carriers and sustained-release microcapsules encapsulating calcium sources and nutrients. Systematic evaluations were conducted, encompassing microbial viability, cement slurry rheology, fluid loss control, anti-channeling capability, and the mechanical strength, permeability, and microstructural characteristics of set cement stones. Results demonstrated that fly ash outperformed blast furnace slag and nano-silica as a carrier, exhibiting superior microbial loading capacity and viability. Optimal performance was observed with additions of 3% microorganisms and 3% microcapsules to the cement slurry. Microscopic analysis further revealed effective calcium carbonate precipitation within and around micro-pores, indicating a self-healing mechanism. These findings highlight the significant potential of the proposed system to enhance cement sheath integrity through localized self-healing, offering valuable insights for the development of advanced, durable well-cementing materials tailored for challenging downhole environments.

The hard rock stratum will seriously affect the efficiency of deep-sea drilling and greatly increase the cost of drilling operations due to its complexity. In ocean drilling operations, the design of the bit is critical. Therefore, the core bit should be able to drill in a variety of formations, especially in hard rock stratum, with the function of reducing the need to change the bit due to formation changes and improving the drilling efficiency. In this paper, three different core bits were designed according to the hard rock stratum of the seabed: the roller bit, diamond bit and bionic bit. According to the test results, it was observed that: (1) It is fully proven that the roller core bit has the characteristics of stable drilling in hard strata, small torque and high drilling efficiency. The same method can realize the core in shallow soft strata through the setting of drilling parameters. (2) For the diamond bit, the field test data show that the new formula diamond bit has a good adaptability to the changing hard rock strata in this area, with an average rate of penetration (ROP) of 4.4 m/h and a bit life of 137.75 m. (3) For the bionic bit, field experiment data showed that drilling in the formation lithology was gray green tuff, which had a core recovery up to 100%. The average ROP was 1.35 m/h, and the highest ROP was 1.88 m/h. The design and experiment of three kinds of drill bits have effectively solved the technical problem of efficient drilling in deep-sea hard-rock stratum.

The rheology control of water-based drilling fluids at ultra-high temperatures has been one of the major challenges in deep or ultra-deep resource exploration. In this paper, the effects of 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonimide) (ILA), 1-ethyl-3-methylimidazolium tetrafluoroborate (ILB) and N-methyl, butylpyrrolidinium bis(trifluoromethanesulfonimide) (ILC) on the rheological properties and filtration loss of polymer-based slurries at ultra-high temperatures (200 °C and 240 °C) are investigated by the American Petroleum Institute (API) standards. The results show that ionic liquids with different structures could improve the high-temperature rheological properties of polymer-based drilling fluids. The rheological parameter value (YP/PV) of the polymer-based slurry formulated with ILC is slightly higher than that with ILA at the same concentration, while the YP/PV value of the polymer-based slurry with ILA is slightly higher than that with ILB, which is consistent with the TGA thermal stability of ILA, ILB, and ILC; the thermal stability of ILC with pyrrolidine cations is higher than that of ILA with imidazole cations, and the thermal stability of ILA with bis(trifluorosulfonyl)amide anions is higher than that of ILB with tetrafluoroborate anions. Cation interlayer exchange between organic cation and sodium montmorillonite can improve the rheological properties of water-based drilling fluids. And meantime, the S=O bond in bis(trifluorosulfonyl)amide ions and the hydroxyl group of sodium montmorillonite may form hydrogen bonds, which also may increase the rheological properties of water-based drilling fluids. ILA, ILB, and ILC cannot reduce the filtration loss of polymer-based drilling fluids at ultra-high temperatures.

Lightweight and ultra-lightweight solid materials are being used in gravel packing for horizontal wells instead of traditional quartz and ceramsite to decrease the risk of premature plugging and improve packing efficiency. Physical and numerical simulation experiments of gravel packing were conducted to assess the effectiveness of reducing solid material density and investigate its impact on packing and sand control. Packed gravel destabilization experiments highlighted the importance of high-compaction degree packing for effective sand control. Further gravel packing experiments examined the packing performance of different solid materials, revealing that lightweight solids have minimal gravitational deposition effect because their density is similar to the gravel slurry, relying primarily on fluid flow for compaction. The numerical simulation indicated that lightweight ceramsite is unsuitable for horizontal and highly-deviated wells because of its poor compaction degree and sand control, especially with high-viscosity slurry. High-density particles enhance gravitational deposition, improving packing compaction and sand control. Lightweight materials are recommended only when advanced plugging of α wave packing cannot be avoided. In highly-deviated wells, high-density materials significantly improve packing stability and sand control. This study provides clear technical guidelines for selecting solid materials for gravel packing in horizontal and highly-deviated wells.

Sand production poses a significant problem for marine natural gas hydrate efficient production. However, the bottom hole gas–water–sand inflow pattern remains unclear, hindering the design of standalone screen and gravel packing sand control completions. Therefore, gas–water–sand inflow patterns were studied in horizontal and vertical wells with the two completions. The experimental results showed that gas–water stratification occurred in horizontal and vertical standalone screen wells. The gas–water interface changed dynamically, leading to an uneven screen plugging, with severe plugging at the bottom and high permeability at the top. The high sand production rate and low well deviation angle exacerbated screen plugging, resulting in a faster rising rate of the gas–water interface. The screen plugging degree initially decreased and then increased as the gas–water ratio increased, resulting in the corresponding variation in the gas–water interface rising rate. Conversely, gas–water stratification did not occur in the gravel packing well because of the pore throat formed between the packing gravels. However, the impact of gas and water led to gravel rearrangement and the formation of erosion holes, causing sand control failure. A higher gas–water ratio and lower packing degree could result in more severe destabilization. Therefore, for the standalone screen completion, sand control accuracy should be designed at different levels according to the uneven plugging degree of the screen. For the gravel packing completion, increase the gravel density without destabilizing the hydrate reservoir, and use the coated gravel with a cementing effect to improve the gravel layer stability. In addition, the screen sand control accuracy inside the gravel packing layer should be designed according to the sand size to keep long-term stable hydrate production.