The rheological properties of sands conditioned with different conditioners and injection ratios were examined. The conditioned sands were prepared with a 40% and 60% volume injection ratio of a bentonite slurry or a carboxymethyl cellulose (CMC) solution. The experiment results show that the tested bentonite-conditioned sand exhibits the characteristics of a Herschel-Bulkley fluid at shear rates in the range of 0–10 s−1 while the CMC-conditioned sand conforms to the power law model. The flow curves of all of the samples show a marked shear-thinning behavior. They also indicated that the existence of a yield stress (τ0) depends only on the rheological behavior of the conditioner and that the yield stress (τ0 if present) and the plastic viscosity (μp) increase with an increase in the volumetric concentration of the sand. Furthermore, to characterize the thixotropy of the conditioned sand, experiments were carried out by using three loading histories with shear rate accelerations of 0.1, 0.2 and 0.4 s−1/s. In the measured results, the thixotropy of the conditioned sand is heavily dependent on the recent flow history. Based on the experimental data, a simple thixotropic prediction model was developed to analyze and predict the transient flow curves of bentonite-conditioned sands.
1 January 2018 in Advances in Materials Science and Engineering
Ground conditioning agents are often needed when performing earth pressure balance shield tunneling in sand soils due to its high internal friction, low plastic ductility, and low compressibility. In this work, vane shear and compression tests for standard sand were performed using a homemade test device, and three types of conditioning agents composed of foam, bentonite slurry, and polymer were used in the tests. The effects of the agents on shear strength and compressibility of the conditioned soils were investigated under a typical earth chamber stress level as high as 2 bar. The measured results show that foam does better in reducing shear strength and improving the compressibility of the conditioned soils than bentonite slurry and polymer. Significant increases in the compressibility of foam‐conditioned soils can be achieved using foam, and the shear strength of the conditioned sand can be decreased by more than 30% with an initial injection ratio of 40% foam. The bentonite‐ and polymer‐conditioned sands have similar compressibility. The HPMC (hydroxypropyl methylcellulose) polymer does better in decreasing the shear strength of the conditioned soils than other liquid soil conditioners. The influences of the device shear rate on the shear strength of the conditioned soils are also presented.
Cutting head clogging is more frequently encountered as more tunnels are being excavated by slurry shield machines. So establishing criteria for cutting head clogging occurrence based on the machine driving parameters is of great engineering significance. Three construction cases of the Beijing south-to-north water diversion auxiliary project, the Jinan Huanghe River Crossing tunnel construction, and the Wuhan Metro Line 8 Yangtze River Crossing tunnel construction, are introduced. Development of the main driving parameters in the construction cases, including the total thrust, the cutting head torque, the advance rate, and the cutting head rotation speed of the tunneling machines before, during, and after the cutting head clogging, are presented and analyzed. The fact is that the total thrust and the cutting head torque of tunneling machines will increase, or will not, once the cutting head clogging occurs. It is recommended to take two combined parameters of total thrust/penetration depth and cutting head torque/penetration depth into account to judge whether the cutting head clogging will occur or not. The maximum increases of the composite parameters by 2–6 times are found in the construction cases. But for the minimum increase, a 30–50% increase of the composite parameter should be noted. The findings can be of great help for similar projects.
18 May 2024 in Tunnelling and Underground Space Technology
Wind speed forecasting is a prerequisite and a guarantee for the efficient operation of wind farms. Estimation of the non-stationary property and prediction of the future moving average of wind speed are challenging because of various environmental factors. In this paper, a new model is proposed for wind speed forecasting. The proposed model consists of three main stages: preprocessing, regression, and aggregation. In the first stage, the original wind speed time series is decomposed into different subseries by using the variational mode decomposition technique. These subseries are then used to construct training patterns and forecasted outputs. In the second stage, support vector regression is applied to fit and forecast the wind speed for each subseries. Eventually, the final forecasted wind speed is calculated by summing all the forecasting values of each subseries. The performance of the proposed model is evaluated using real data collected from a wind farm in China, and the experimental results confirm the superiority of the proposed model to the existing models with respect to accurate forecasting and stability.
Tunnel boring machine (TBM) disc cutters are specially designed for breaking hard rocks and always exhibit unsatisfactory performance during the soft-hard varied stratum tunneling process. To figure out the load and cutting performance of the disc cutter and avoid unsatisfying excavation face crushing effects, a soft-hard varied strata excavation face model was made and rotary cutting tests with full-scale disc cutters were conducted. The load and cutting performance of the disc cutter under different TBM operating conditions were monitored and analyzed based on the test. It was found that the variation of the disc cutter load did not meet the CSM model completely, and the tangential force of the disc cutters in the heterogeneous areas was only about 30–40 % of that in the uniform areas of the excavation face model. An ideal criterion for the excavation face to be crushed successfully was established and the unknown parameters in it were obtained by fitting the test data. The gradation information and fractal dimension of crushing debris were obtained by the sieved-and-weighed method, which can provide indicators for the crushing effect of the disc cutters. Three different disc cutter poor performance modes in the heterogeneous strata cutting process were analyzed: (1) rotating starting failure of the disc cutters caused by tangential load insufficiency, (2) excavation face crushing failure caused by low crack extending capacities of the materials being cut and improper operating parameters (too small cutting depths or too large disc cutter spacing), and (3) adverse excavation face crushing forms (large or powdery debris). These analyses can help with the performance evaluation of disc cutters and the tunneling parameter adoption of the TBM in soft-hard varied strata tunneling engineering.