The metasurface refractive index sensor has a high degree of tunability and flexibility, providing excellent performance for high precision refractive index sensing applications. The metasurface absorber with metallic structure has been hindered in further sensor applications due to the inherent Ohmic loss of the metallic material. In this study, a dual nanorod metasurface structure based on semiconductor Si was designed, introducing a symmetry‐breaking structure to excite dual ultra‐narrow q‐BIC resonance peaks with Fano line shapes. Both peaks are located in the near‐infrared region, and multipole analysis shows that this strong field enhancement effect is induced by a magnetic dipole. Experimental results demonstrate the potential of this sensor to provide dual‐channel detection while achieving high sensitivity and high Q‐factor. We believe that this device exhibits outstanding performance and high practicality, providing a reference for the development and application of biological and environmental sensors.

It is of great significance for the monitoring and protection of the original ecological environment in coal mining areas to identify the ground subsidence and quantify its influence on the surface vegetation. The surface deformation and vegetation information were obtained by using spaceborne SAR and Landsat OLI images in the Xishan Coalfield. The relative change rate, coefficient of variation, and trend analysis methods were used to compare the vegetation growth trends in the subsidence center, subsidence edge, and non-subsidence zones; and the vegetation coverage was predicted by the pixel dichotomy and grey model from 2021 to 2025. The results indicated that the proportions of vegetation with high fluctuation and serious degradation were 6.60% and 5.64% in the subsidence center, and its NDVI values were about 10% lower than that in the subsidence edge and non-subsidence zones. In addition, vegetation coverage showed a wedge ascending trend from 2013 to 2020, and the prediction values of vegetation coverage obtained by GM (1,1) model also revealed this trend. The residuals of the predicted values were 0.047, 0.047, and 0.019 compared with the vegetation coverage in 2021, and the vegetation coverage was the lowest in the subsidence center, which was consistent with the law obtained by using NDVI. Research suggested that ground subsidence caused by mining activities had a certain impact on the surface vegetation in the mining areas; the closer to the subsidence center, the greater the fluctuation of NDVI, and the stronger the vegetation degradation trend; conversely, the smaller the fluctuation, and the more stable the vegetation growth.

To address the shortcomings in many traditional spectral feature extraction algorithms in practical application of low modeling accuracy and poor stability, this paper introduces the “Boruta algorithm-based local optimization process“ based on the traditional simulated annealing algorithm and proposes the “two-step simulated annealing algorithm (TSSA)”. This algorithm combines global optimization and local optimization. The Boruta algorithm ensures that the feature extraction results are all strongly correlated with the dependent variable, reducing data redundancy. The accuracy and stability of the algorithm model are significantly improved. The experimental results show that compared with the traditional feature extraction method, the accuracy indexes of the inversion model established by using the TSSA algorithm for feature extraction were significantly improved, with the determination coefficient R² of 0.9654, the root mean square error (RMSE) of 3.6723 μg/L, and the mean absolute error (MAE) of 3.1461 μg/L.

Analyzing three-dimensional (3D) phenotypic parameters of maize seedlings is of significant importance for maize cultivation and selection. However, existing methods often struggle to balance cost, efficiency, and accuracy, particularly when capturing the complex morphology of seedlings characterized by slender stems. To address these issues, this study proposes a novel end-to-end automated framework for extracting phenotypes using only consumer-grade RGB cameras. The pipeline initiates with Instant-NGP to rapidly reconstruct dense point clouds, establishing the 3D data foundation for phenotypic extraction. Subsequently, we formulate a directed topological graph-based mechanism. By mathematically defining bifurcation constraints via vector analysis, this mechanism guides a depth-first traversal strategy to explicitly disentangle stem and leaf skeletons. Building upon these decoupled skeletons, organ-level point cloud segmentation is achieved through constraint-based expansion, followed by density-based spatial clustering (DBSCAN) to detect individual leaves. Algorithms combining point cloud geometry with 3D Euclidean distance are also implemented to calculate key phenotypes including plant height and stem width. Finally, single-leaf skeleton fitting is used to estimate leaf length, and principal component analysis (PCA) is adopted to determine the stem–leaf angle, realizing the comprehensive automatic extraction of maize seedling phenotypes. Experiments show that the proposed method achieves high accuracy in extracting key phenotypic parameters. The mean relative errors for plant height, stem width, leaf length, stem-leaf angle, and leaf area are 0.76%, 2.93%, 1.26%, 2.13%, and 3.33%, respectively. Compared with existing methods as far as we know, the proposed method significantly improves extraction efficiency by reducing the processing time per plant to within 5 min while maintaining such high accuracy.