Yu ZHENG

Yu ZHENG


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 February 2022 in Energies
Verified
Journal Article
Open access
PDF file
YZYu ZHENG
Yu ZHENG
WYWenlong Yin
Wenlong Yin
WZWenjie Zhang
Wenjie Zhang
JLJinhan Liang
Jinhan Liang
KLKangyong Liu
Kangyong Liu
KWKuan Wang
Kuan Wang
In response to extreme climate change, China has set a goal of reaching emission peak by 2030 and achieving carbon neutrality by 2050. Energy conservation and emission reduction of building heating in northern China are key to achieving this goal. Based on building area prediction and energy consumption intensity, this paper establishes a model for calculating heating energy consumption and carbon emissions in northern residential buildings at the macro level, which provides a basis for formulating policies related to heating and emission reduction in northern buildings. Based on the research method of scenario projection, combining the carbon emission subsets and future heating energy mix projections in northern China, the heating energy consumption in northern China decreases to 175, 149 and 135 Mtce in 2050 under the baseline, medium control and strict control scenarios, respectively. The heating energy consumption in the northern region should be controlled at least under the medium control scheme. Under this scenario, building heating carbon emissions in the north could be reduced to 450 MtCO2 by 2050, or 280 MtCO2 if more stringent abatement technologies are adopted. In order to achieve this goal, a combination of energy-saving technologies must be used. The use of biomass and solar technologies should be emphasized in rural heating, while envelope renovation makes the greatest contribution to heating energy savings, with envelope renovation contributing up to 92 Mtce to urban heating.

30 August 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
YZYu ZHENG
Yu ZHENG
XLXiaoming Li
Xiaoming Li
WZWenjie Zhang
Wenjie Zhang
KWKuan Wang
Kuan Wang
FHFeng Han
Feng Han
YZYuqiang Zhao
Yuqiang Zhao
In this paper, a phase change microcapsule suspension MPCMS25 with a mass fraction of 10% was prepared with TH-ME25 as the phase change microcapsule particles and deionized water as the base fluid. The experimental benches of the Building Integrated Photovoltaic (BIPV) system and BIPV-MPCMS system were set up, and the comparative tests were carried out in Nanjing to study the optimization effect of phase change microcapsule suspension on the thermal and electrical properties of the BIPV system. The results show that MPCMS25 reduces the component temperature of the system by 8.8 °C and the backplane temperature by 11.1 °C. The optimization time of the component operating temperature and the backplane temperature is 9.5 h and 9.75 h, respectively. Delay appearance of peak module operating temperature by 114 min and peak backplane temperature by 125 min. In addition, the suspension can also improve the power conversion efficiency (PCE) of photovoltaic modules by 0~5%. After a simulation study on the energy consumption of a high-speed railway station, it is found that using the BIPV-MPCMS system as the building envelope can achieve an energy saving rate of about 8.5%.

22 January 2024 in Buildings
Verified
Journal Article
Open access
PDF file
YZYu ZHENG
Yu ZHENG
CLChunfang Lu
Chunfang Lu
XHXiaomin Huang
Xiaomin Huang
WXWeibing Xu
Weibing Xu
DZDaxing Zhou
Daxing Zhou
YSYulong Sun
Yulong Sun
To study how varying the parameters of expansion joints and bearing supports (E-B parameters) affects the dynamic response of a coupled vehicle–bridge system for curved girder bridges, a dynamic response analysis method for the coupled vehicle–joint (bearing)–bridge system, which takes into account centrifugal forces, was proposed and verified. Subsequently, taking a continuous curved box girder bridge as the prototype, the influence of the E-B parameters on the vehicle-induced dynamic response of the curved girder bridge was explored. The results showed that the dynamic amplification factor (DAF) of the middle beam of the expansion joint (DAF-EJ) and the main girder of the curved bridge (DAF-MG) were both significantly influenced by the E-B parameters. When there were height differences between the middle beam and side beam in the EJ, the DAF-EJ obviously varied, and the DAF-MG increased. When the EJ was damaged, the impact effect of the vehicle on the bearing support increased. The DAF-EJ and DAF-MG both increased with the decrease of the vertical support stiffness of the bearing support. The DAF-EJ was greatly affected by the single-support void at the near-slit end of the lane. The DAF-MGs at the beam end, the 1/4 point and 1/2 point of the first span, and the 1/2 point of the second span, were significantly affected by the single-support void near the measuring point. Compared with the single-support void, the DAF-EJ and DAF-MG more significantly increased under the double-support void. Variation in the height difference of the EJ had a more significant effect on the DAF-EJ and DAF-MG at the beam end, while a vertical stiffness reduction in the bearing support had a more significant effect on the DAF-MG.