Graphene oxide (GO) and multi-walled carbon nanotubes (MWCNT) were incorporated into a SiOC composite ceramic matrix using a simple roll-mixing method followed by thermal cross-linking and pyrolysis. The structure, morphology, porosity, surface characteristics, and thermal properties of polysiloxane are analysed using scanning electron microscopy, BET specific surface area, mercury intrusion porosimetry, water vapour and n-heptane adsorption, and Raman spectroscopy, respectively. The electrical conductivity, conduction mechanism, and percolation behavior of the composite ceramics are investigated by electrical impedance spectroscopy in the temperature range of 25–250 °C. Free-rising composite ceramic foams are generated, incorporating both nanofillers into the SiOC ceramic matrix. Both nanofillers show a positive effect on the thermal stability of the SiOC ceramics. The room temperature DC conductivity value of pure SiOC ceramics shows ∼2.97 × 10−9 S cm−1, which increases by three to four orders of magnitude after the incorporation of 5 wt% conductive nanofillers (∼2.5 × 10−6 S cm−1 for 5 wt% GO and ∼2.08 × 10−5 S cm−1 for 5 wt% MWCNT). The calculated activation energy from the Arrhenius plot for composite ceramics is found to be lower (0.10 eV for 5 wt% GO and 0.07 eV for 5 wt% MWCNT) compared to the same SiOC ceramics without nanofillers (0.22 eV). The conduction mechanism studies of composite ceramics suggest a non-Debye type distribution of relaxation in SiOC. Thus the nanofiller-enhanced SiOC ceramics are highly promising materials for rechargeable batteries, high-temperature fuel cells, gas sensors, display devices etc.
Cobalt/nickel-containing SiOC-based porous ceramic electrocatalysts were prepared by pyrolysis of poly(methyl silsesquioxane) and poly(methyl phenyl silsesquioxane) as preceramic precursors combined with graphite and Co/Ni metal salts at 1000 °C in an atmosphere of nitrogen. Subsequently, the Co/Ni–SiOC materials were N-doped using dicyandiamide (DCDA) as a nitrogen source and pyrolysed at 800 °C in an inert atmosphere. The structural properties and composition of the catalysts were characterised by scanning electron microscopy (SEM), X-ray diffraction, X-ray photoelectron spectroscopy (XPS) and N2 adsorption analysis. The evaluation of the polymer-derived SiOC(N) ceramic electrocatalysts as a new class of catalysts for the oxygen reaction reduction (ORR) was carried out by the rotating disk electrode (RDE) method under acidic, neutral and alkaline conditions. The O2 reduction studies revealed that the N-doped materials exhibited enhanced ORR performance, confirming the positive influence of the nitrogen functionalities introduced into the catalysts. The Co-containing N-doped SiOC catalyst exhibited significantly higher ORR activity compared with the studied materials along with the highest electron transfer number in all the studied solutions. Long-term ORR performance testing indicated that the durability of this catalyst was superior as compared to that of commercial Pt/C. These observations suggest that the Co-containing N-doped SiOC catalyst is a promising cathode material for fuel cells (FCs) and microbial FC devices.
23 December 2013 in Journal of the American Ceramic Society
Micro‐ and macroporous monoliths with in situ formed nickel nanoparticles were prepared for the first time by the combination of solution‐based freeze casting and preceramic polymers (methyl polysiloxane). This one‐step process results in macroporous monoliths composed of microporous and catalytic active nickel‐containing polymer‐derived ceramic. Four different complexing and cross‐linking siloxanes with amino functionality were screened for their ability to create small nickel particles. TEM analysis confirmed 3‐aminopropyltriethoxysilane being most efficient. High BET‐specific surface areas of 344‐461 m2 g−1 were achieved. Increased ratio of complexing groups to nickel improves the dispersion of nickel to (3.61 ± 1.49) nm. The nickel size dependence of conversion (maximum 0.49) and CH4 selectivity (maximum 0.74) in CO2 methanation emphasizes the importance of controlling the nickel size. The hydrophobic surface characteristic is hypothesized to be the main reason polymer‐derived catalysts having better catalytic activity compared with nickel‐impregnated silica. The promising catalytic activity combined with the versatile freeze casting process can prospectively address heat‐ and mass‐transfer considerations in heterogeneous monolith catalysis.