Xiang Xu

Dr. Xiang Xu

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2021 in Shock and Vibration
Verified
Journal Article
Open access
PDF file
XZXinze Zhao
Xinze Zhao
YNYunfeng Nie
Yunfeng Nie
MCMing Chen
Ming Chen
HQHongling Qin
Hongling Qin
XXXiang Xu
Xiang Xu
In this paper, the contact characteristics of the carbon brush/slip ring of the hydrogenerator under the eccentric vibration of the rotor are studied. The influence of spring parameters on the contact loss of the carbon brush/slip ring was studied by establishing the motion model of the carbon brush/slip ring for theoretical calculation and fitting the motion trajectory curve with MATLAB software. Studies have shown that the loss of contact is mainly related to the spring damping coefficient and the precompression. By optimizing these two parameters, the contact stability of the carbon brush on the ring surface of the slip ring can be improved. It provides a theoretical reference for the design and optimization of the parameters of the carbon brush/slip ring spring.

1 December 2020 in Wear
Verified
Journal Article
Closed access
XZXinze Zhao
Xinze Zhao
DSDan Su
Dan Su
XXXiang Xu
Xiang Xu
YDYang Dong
Yang Dong
ZGZhuanghui Gong
Zhuanghui Gong

13 September 2023 in Lubricants
Verified
Journal Article
Open access
PDF file
XXXiang Xu
Xiang Xu
ZFZekang Feng
Zekang Feng
NXNengqi Xiao
Nengqi Xiao
XZXinze Zhao
Xinze Zhao
ZZZuyue Zhang
Zuyue Zhang
The three-dimensional morphology of frictional sub-surfaces holds significant importance for studying tribological issues. However, the uniformity of the horizontal datum in 3D scanning is limited for curved surfaces, resulting in the inability to obtain accurate contour characterization parameters from the scanning results. This study aims to address this issue by constructing regular surface equations and normalizing the 3D profiler scanning results. By fitting the data, a “plane” surface representative of the surface features is obtained, and the paper demonstrates this approach on the surface morphology of different worn parts in the frictional area of spherical bearings located in the specific environment of the Three Gorges gate. The results indicate that the obtained “plane” effectively reconstructs the three-dimensional morphology map of the regular surface. Moreover, this reconstructed plane not only clearly illustrates the surface characteristics but also provides the foundation for analyzing the wear mechanism.

13 May 2026 in Lubricants
Verified
Journal Article
Open access
PDF file
XXXiang Xu
Xiang Xu
XMXingyu Ma
Xingyu Ma
CSChang Sun
Chang Sun
HWHaihua Wu
Haihua Wu
XZXinze Zhao
Xinze Zhao
MZMeiyun Zhao
Meiyun Zhao
Conventional solid-inlay lubrication research has focused on the overall inlay layout and generalized lubrication effects; localized inlay lubrication enables precise release of the lubricant and rapid formation of a uniform and dense lubricant film. The aim of this study is to use a combination of simulations and experimentation to establish a localized spherical friction pair containing a filled-hole structure, so that optimal lubrication can be predicted accurately. We designed seven different kinds of localized annular band inlay axial tiles, with ratios of 10, 12, 15, 18, 20, 22, and 25; carried out a transient mechanical analysis through finite element software, comparing the equivalent stress and friction coefficient of the inlay tiles with different ratios; and conducted friction wear tests through a self-developed spherical wear test bench. The friction surfaces of the tested specimens were analyzed for sliding friction coefficients and wear, as well as by SEM surface and EDS analyses. The results show that the best mechanical properties and the smallest theoretical friction coefficients are obtained when the relative ratio of the ring diameter to inlay hole diameter is 25. This study provides a theoretical basis for the design of spherical solid-inlay lubrication structures in the region of the split-belt ring design.

10 August 2026 in Coatings
Verified
Journal Article
Open access
PDF file
WLWanting Li
Wanting Li
XZXinze Zhao
Xinze Zhao
WYWei Yang
Wei Yang
XXXiang Xu
Xiang Xu
XZxiaolong zhang
xiaolong zhang
To clarify the origin of asymmetric arc ablation in hydroelectric generator slip rings, a Steel 45/carbon current-carrying friction pair was selected to investigate the influence of current polarity on arc behaviour and interfacial damage. Static gap discharge tests (10 A) and dynamic tests (current density of 10 A/cm2, sliding velocity of 0.419 m/s) were performed to characterize polarity-dependent erosion behaviour. The results indicate that, under the steel(+)–carbon(−) condition, the arc exhibits unstable burst-like discharge accompanied by intense spark spattering. The carbon cathode experiences severe material loss due to the combined effects of cathode-spot heating, positive-ion bombardment, and molten metal droplet impact. The steel surface is characterized by nested erosion pits and spherical resolidified spatter particles, while the apparent ablation-affected area shows an overall increase with accumulated arc duration, with a more pronounced expansion observed at longer durations. Pronounced bidirectional material migration and interfacial elemental enrichment are observed under the steel(+)–carbon(−) configuration, resulting in an apparent net mass loss rate approximately 2.5 times higher than that under the steel(-)–carbon(+) configuration. The reversed steel(−)–carbon(+) configuration produces a spatially constrained and stable arc discharge, accompanied by a continuous remelted layer and network-like thermal-stress cracks on the steel surface. Polarity reversal changes the direction of the interfacial electric field and charged-particle migration, thereby regulating cathode electron emission, arc discharge behaviour, energy distribution in the near-electrode region, and bidirectional material migration across the interface. These results provide a theoretical basis for elucidating the polarity-dependent arc ablation mechanism of steel/carbon friction pairs and for optimizing polarity configuration and differentiated protection strategies for hydroelectric generator slip rings.

30 September 2026 in Coatings
Verified
Journal Article
Open access
PDF file
YLYang Li
Yang Li
XZXinze Zhao
Xinze Zhao
WLWanting Li
Wanting Li
YLYunhui Li
Yunhui Li
HWHailin Wu
Hailin Wu
WYWei Yang
Wei Yang
To elucidate the influence of ring-chamber dust on the current-carrying tribological behavior of the carbon brush/collector ring system in hydro-generators, D172 carbon brushes paired with 45 steel collector rings were employed as the research subjects. Current-carrying sliding friction tests were systematically conducted under varying concentrations of carbon powder, iron powder, and carbon–iron mixed powders. The evolution of friction coefficient, wear loss, wear rate, and contact resistance was analyzed in detail, while the worn carbon brush specimens were characterized using three-dimensional profilometry, scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The results demonstrate that different wear debris powders, serving as third-body media, exert significant regulatory effects on both interfacial tribological and electrical conduction behaviors. Under the carbon powder condition, a relatively stable carbonaceous third-body layer readily forms at the interface, maintaining low friction coefficient and wear rate—both reaching their minima at 120 mg/min—thus demonstrating effective friction reduction and wear resistance. In contrast, iron powder conditions promote pronounced abrasive action induced by hard particles, which increases the friction coefficient, accelerates carbon brush wear, and deteriorates the interfacial contact state. For carbon–iron mixed powders, the friction and wear levels lie between those observed for pure carbon and pure iron powders; meanwhile, contact resistance decreases steadily with increasing powder supply rate, indicating relatively superior current-carrying stability. The study reveals that carbon powder primarily contributes positively through lubrication and interfacial protection, whereas iron powder exacerbates damage via particle plowing and contact disruption. The synergistic interaction between the two determines the evolution of the interfacial film layer and the resulting changes in electrical contact performance. These findings provide a theoretical basis for wear control and operational maintenance of carbon brush systems in hydro-generators.