Metal Big Area Additive Manufacturing (MBAAM) is a novel wire-arc additive manufacturing method that uses a correction-based approach developed at the Oak Ridge National Laboratory (ORNL). This approach is an integrated software method that minimizes the dynamic nature of welding and compensates for build height. The MBAAM process is used to fabricate simple geometry thin walled specimens, using a C-Mn steel weld wire, to investigate the scatter in mechanical properties and correlate them to the underlying microstructure. The uni-axial tensile tests show isotropic tensile and yield properties with respect to building directions, although some scatter in elongation is observed. Large scatter is observed in the Charpy Impact tests. The microstructure characterization reveals mostly homogenous ferrite grains with some pearlite, except for some changes in morphology and grain size at the interface between the build and the base plate. The measured properties and microstructure are compared with the toughness and strength values reported in the literature, and a hypothesis is developed to rationalize the differences. Overall, the MBAAM process creates stable, isotropic, and weld-like mechanical properties in the deposit, while achieving a precise geometry obtained through a real-time feedback sensing, closed loop control system.

Fiber optic sensors have long been considered for use in structural health monitoring of components because of their small size, high accuracy, and their ability to perform spatially distributed strain measurements when embedded within a component or on its surface. The typical method for transferring strain from the component to the fiber is to use an epoxy, which may not survive extended exposure to high temperatures, thus necessitating a more elaborate technique to embed the fibers. This work represents a first step towards using additive manufacturing techniques to embed fiber optic sensors on stainless steel components for high-temperature strain monitoring, including quantification of the differential thermal strains that develop between the fiber and the steel substrate. Copper-coated optical fibers were embedded in nickel layers on top of a stainless steel substrate using an ultrasonic additive manufacturing technique. The embedded fibers showed minimal signal attenuation and clear compressive strain after embedding. Heating the embedded fibers in steps to temperatures of 300 °C–400 °C resulted in measured strains with values between the expected thermal strain in stainless steel and nickel. Finite element simulations confirm the measured strain values and show that the thermal strain depends on the thickness of the nickel layers deposited on top of the stainless steel substrate. While the fibers failed before reaching temperatures of 500 °C, it is suspected that these failures occurred due to a combination of (1) the lack of strain relief, (2) the high-temperature oxidation of the fiber’s copper coating, and (3) improper sizing of the machined channel in which the fiber is placed prior to embedding. If proper coating selection and sizing of the channel can prevent the failures observed in this work, the next step would be to monitor strain during mechanical loading at high temperatures.

Ultrasonic additive manufacturing (UAM) is a solid-state manufacturing process for making complex components. However, fabrication of ferritic (body centered cubic) steels has been challenging for UAM due to its high hardness. This research successfully joined AISI 4130 steel sheets by using soft Ni (face centered cubic) interlayers. The localisation of plastic deformation in the Ni-interlayer leads to a significant reduction in voids. A post-process heat-treatment was designed using thermodynamic calculations to dissolve nickel into steel matrix. Energy dispersive X-ray spectroscopy measurements showed ∼10 µm Ni from the interlayer diffused into the steel side, confirming the feasibility of the approach. The shear tests show a higher shear strength in comparison to as-processed 4130 without interlayers and post processed using hot isostatic pressing (HIP).

Driven by the interest to weld steel and aluminium in the solid state to prevent intermetallic formation, 9 kW ultrasonic additive manufacturing (UAM) has been used to fabricate Al 6061-4130 steel dissimilar metal builds. In addition, Al 6061-Al-6061 builds were fabricated using similar techniques to provide a baseline for mechanical property measurement. Mechanical testing performed using pushpin testing shows that steel–aluminium dissimilar metal welds fail across multiple layers while Al–Al welds delaminate from the substrate. Multi-scale characterisation indicates that the change in failure morphology is due to the formation of metallurgical bonds in the Al–steel builds. Texture analysis shows identical textures at the interface of Al–steel, Al–Al and Al–Ti joints; showing that the bond formation in all cases relies extensively on plastic deformation across multiple materials. In addition, no changes to the bonding mechanism occurred when the materials used as foils and substrate were swapped.

Advanced manufacturing (AM) is a disruptive manufacturing process often referred to as “the next industrial revolution” because of its ability to fabricate components with complex geometries and site-specific materials and properties. While other industries, like automotive, aerospace, and fossil-fired power companies, are adopting and evaluating AM processes, the nuclear industry, including the fusion materials community, has been somewhat slow to capitalize on the seemingly beneficial aspects of AM. To address this gap, Oak Ridge National Laboratory is evaluating candidate AM techniques to fabricate nuclear-relevant materials including ferritic-martensitic (FM) steels. This paper discusses the development of a road map for AM approaches for FM steels. Specifically, the connection among alloy composition, additive processes, processing conditions, and postprocessing and the resulting microstructure using both wire-based and powder-based directed energy deposition techniques is detailed. Finally, strategies to develop specialized alloys for additive manufacturing are outlined.