The large-amplitude sloshing behavior of liquid hydrogen in a tank for heavy-duty trucks may have adverse effects on the safety and stability of driving. With successful application of liquid hydrogen in the field of new energy vehicles, the coupled thermodynamic performance during liquid hydrogen large-amplitude sloshing becomes more attractive. In this paper, a three-dimensional numerical model is established to simulate the thermodynamic coupling characteristics during liquid hydrogen sloshing in a horizontal tank for heavy-duty trucks. The calculation results obtained by the developed model are in good agreement with experimental data for liquid hydrogen. Based on the established 3D model, the large-amplitude sloshing behavior of liquid hydrogen under extreme acceleration, as well as the effects of acceleration magnitude and duration on liquid hydrogen sloshing, is numerically determined. The simulation results show that under the influence of liquid hydrogen large-amplitude sloshing, the convective heat transfer of fluid in the tank is greatly strengthened, resulting in a decrease in the vapor temperature and an increase in the liquid temperature. In particular, the vapor condensation caused by the sloshing promotes a rapid reduction of pressure in the tank. When the acceleration magnitude is 5 g with a duration of 200 ms, the maximum reduction of ullage pressure is 1550 Pa, and the maximum growth of the force on the right wall is 3.89 kN. Moreover, the acceleration magnitude and duration have a remarkable influence on liquid hydrogen sloshing. With the increase in acceleration magnitude or duration, there is a larger sloshing amplitude for the liquid hydrogen. When the duration of acceleration is 200 ms, compared with the situation at the acceleration magnitude of 5 g, the maximum reductions of ullage pressure decrease by 9.46% and 55.02%, and the maximum growth of forces on the right wall decrease by 80.57% and 99.53%, respectively, at 2 g and 0.5 g. Additionally, when the acceleration magnitude is 5 g, in contrast with the situation at a duration of acceleration of 200 ms, the maximum-ullage-pressure drops decrease by 8.17% and 21.62%, and the maximum increase in forces on the right wall decrease by 71.80% and 88.63%, at 100 ms and 50 ms, respectively. These results can provide a reference to the safety design of horizontal liquid hydrogen tanks for heavy-duty trucks.
Efficient insulation technology is one of the key technologies for the development of large LH2 storage tanks. This paper aimed at a 4000 m3 LH2 spherical tank, many insulation schemes were designed, including multilayer insulation systems integrated with a vapor-cooled shield (VCS) and liquid-nitrogen-cooled shield (LN2CS). The heat transfer model was developed to predict the insulation performance of a LH2 spherical tank. The effect of the VCS position on insulation performance was studied, and the different configurations of double VCSs were compared and discussed. The results showed that the daily evaporation rate of MLI, hollow glass microspheres (HGMs) and vacuum was only 2.05 × 10−3%, 3.62 × 10−3% and 7.94 × 10−2% at 1.34 Pa, respectively. MLI was still the optimal insulation scheme for a 4000 m3 LH2 spherical tank. Meanwhile, it was found that when the single VCS was placed at the 10th layer, the heat leakage was reduced by approximately 40.5% compared with MLI. The heat leakage of parallel VCS(P-VCS) was 76.6% lower than that of MLI. The minimum heat leakage of series VCS(S-VCS) was 83.79%, 72.75% and 37.36% lower than that of MLI, single VCS and P-VCS, respectively. Additionally, the heat leakage of the LH2 tank could be reduced to less than 10 W when LN2CS was installed. These results provide a design reference for the highly efficient storage of large LH2 tanks.
A four-node model is proposed to investigate the no-vent filling performance of liquid hydrogen (LH2) at microgravity. The no-vent filling method can directly prevent the influence of random gas–liquid distributions at microgravity, making it a good choice for cryogenic propellants to achieve orbital refueling. The typical phase distribution of the centrally located ullage was assumed and, in particular, the correlations for the boiling heat transfer of LH2 at microgravity were corrected in this model. After the accuracy of this model was effectively verified, the effects of different filling conditions, including the initial tank pressure, the initial temperature, and the temperature of the inlet liquid, were studied. The results showed that the initial pressure had a major influence on the initial pressure rise but only a slight influence on the final pressure development. A higher initial temperature would have led to an obvious increase in the tank pressure and an obvious decrease in the final filling level when reaching the upper pressure limit. Reducing the temperature of the inlet liquid has certain effects on the pressure control and the improvement of the final filling level. In conclusion, to achieve a higher filling level under a lower pressure level during the no-vent filling of LH2 at microgravity, sufficient pre-cooling of the filling system is required. Furthermore, appropriate evacuation of the receiver tank before filling and subcooling of the inlet liquid within an acceptable range of costs are both suggested. While the proposed model is less accurate than full-resolution CFD for the detailed evolution of physical fields, it offers much greater computational speed for quick parametric studies of key input conditions.
Densified liquid hydrogen/liquid oxygen is a promising propulsion fuel in the future. In order to systematically demonstrate the benefits and challenges of densified liquid hydrogen/liquid oxygen, a transient thermodynamical model considering the heat leakage, temperature rise, engine thrust, pressurization pressure of the tank, and wall thickness of tank is developed in the present paper, and the performance of densified liquid hydrogen/liquid oxygen as propulsion fuel is further evaluated in actual application. For liquid hydrogen/liquid oxygen tanks at different structural dimensions, the effects of many factors such as temperature rise during propellant ground parking, lift of engine thrust, mass reduction of the tank structure, and extension of spacecraft in-orbit time are analyzed to demonstrate the comprehensive performance of liquid hydrogen/liquid oxygen after densification. Meanwhile, the problem of subcooling combination matching of liquid hydrogen/liquid oxygen is proposed for the first time. Combining the fuel consumption and engine thrust lifting, the subcooling combination matching of liquid hydrogen/liquid oxygen at different mixing ratios and constant mixing ratios are discussed, respectively. The results show that the relative engine thrust enhances by 6.96% compared with the normal boiling point state in the condition of slush hydrogen with 50% solid content and enough liquid oxygen. The in-orbit time of spacecraft can extend about 2–6.5 days and 24–95 days for slush hydrogen with 50% solid content and liquid oxygen in the triple point state in different cryogenic tanks, respectively. Due to temperature rise during parking, the existing adiabatic storage scheme and filling scheme for densification LH2 need to be redesigned, and for densification LO2 are suitable. It is found that there is an optimal subcooling matching relation after densification of liquid hydrogen/liquid oxygen as propulsion fuel. In other words, the subcooling temperature of liquid hydrogen/liquid oxygen is not the lower the better, but the matching relationship between LH2 subcooling degree and LO2 subcooling degree needs to be considered at the same time. It is necessary that the LO2 was cooled to 69.2 K and 54.5 K, when the LH2 of 13.9 K and SH2 with 45% was adopted, respectively. This research provides theoretical support for the promotion and application of densification cryogenic propellants.