Yuan Ma

Dr. Yuan Ma

Institute of Refrigeration and Cryogenic Engineering, Xi'an Jiaotong University, Xi'an 710049, China
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 April 2023 in Processes
Verified
Journal Article
Open access
PDF file
Yuan MaYuan Ma
Yuan Ma
YZYue Zhang
Yue Zhang
XLXiaozhong Luo
Xiaozhong Luo
Yanzhong LiYanzhong Li
Yanzhong Li
Fushou XieFushou Xie
Fushou Xie
A four-node model is proposed to investigate the no-vent filling performance of liquid hydrogen (LH2) at microgravity. The no-vent filling method can directly prevent the influence of random gas–liquid distributions at microgravity, making it a good choice for cryogenic propellants to achieve orbital refueling. The typical phase distribution of the centrally located ullage was assumed and, in particular, the correlations for the boiling heat transfer of LH2 at microgravity were corrected in this model. After the accuracy of this model was effectively verified, the effects of different filling conditions, including the initial tank pressure, the initial temperature, and the temperature of the inlet liquid, were studied. The results showed that the initial pressure had a major influence on the initial pressure rise but only a slight influence on the final pressure development. A higher initial temperature would have led to an obvious increase in the tank pressure and an obvious decrease in the final filling level when reaching the upper pressure limit. Reducing the temperature of the inlet liquid has certain effects on the pressure control and the improvement of the final filling level. In conclusion, to achieve a higher filling level under a lower pressure level during the no-vent filling of LH2 at microgravity, sufficient pre-cooling of the filling system is required. Furthermore, appropriate evacuation of the receiver tank before filling and subcooling of the inlet liquid within an acceptable range of costs are both suggested. While the proposed model is less accurate than full-resolution CFD for the detailed evolution of physical fields, it offers much greater computational speed for quick parametric studies of key input conditions.

1 November 2020 in Applied Thermal Engineering
Verified
Journal Article
Closed access
Yuan MaYuan Ma
Yuan Ma
KZKang Zhu
Kang Zhu
Yanzhong LiYanzhong Li
Yanzhong Li
Fushou XieFushou Xie
Fushou Xie

18 November 2022 in Processes
Verified
Journal Article
Open access
PDF file
Chengfeng ZhuChengfeng Zhu
Chengfeng Zhu
Yanzhong LiYanzhong Li
Yanzhong Li
Fushou XieFushou Xie
Fushou Xie
Lei WangLei Wang
Lei Wang
Yuan MaYuan Ma
Yuan Ma
In the propulsion system of cryogenic liquid rockets, low-frequency pressure oscillation is a long-standing issue occurring in its feeding pipe, and is not conducive to the normal operation of the rocket. Its mechanism and excitation process are not very clear due to the limitation of the existing numerical method and the difficulty of the real dynamic experiment. Inspired by the periodic suck-back flow phenomenon of steam condensation, the fluctuation of the two-phase interface might be the crucial factor to initiate the low-frequency pressure oscillation. To simulate this interfacial characteristic of cryogenic propellant, a novel numerical model is proposed to predict the mass transfer rate weighted by the interfacial curvature. Aiming at the oxygen jet condensation simulation, the low-frequency pressure oscillation phenomenon is obtained successfully with the excitation frequency of 10.6 Hz, consistent with the natural frequency of the engine test run. It is conducted so the low-frequency pressure oscillation is caused by the periodic condensation of the continuous oxygen vapour plume, along with an oxygen suck-back flow phenomenon. In addition, the results indicate that both the oxygen and liquid oxygen mass flux promote the rise in the frequency of pressure oscillation. These conclusions provide theoretical instructions for the design and operation of the propulsion system of a cryogenic liquid rocket.

20 April 2023 in Processes
Verified
Journal Article
Open access
PDF file
JLJiajia Liang
Jiajia Liang
Yuan MaYuan Ma
Yuan Ma
Yanzhong LiYanzhong Li
Yanzhong Li
Lei WangLei Wang
Lei Wang
XLXiaozhong Luo
Xiaozhong Luo
A thermal equilibrium model is established to investigate the heat leak of a space liquid hydrogen tank under different thermal adiabatic structures. The feasibility of the common bulkhead tank in realizing thrust or rotation reorientation by evaporated exhaust gas has been systematically studied. The results indicate that the space radiation heat leak is the primary heat leak in spray-on foam insulation (SOFI) adiabatic tanks. However, the common bulkhead heat leak is dominant in the tank with multilayer insulation (MLI) or self-evaporation vapor cooled shield (VCS). For the continuous stable adiabatic exhaust, the tank with SOFI (over 114 W/m2) could realize reorientation with the acceleration of over 5.5 × 10−4 m/s2 generated by the exhaust. Meanwhile, the tank that adopted MLI or VCS (below 18 W/m2) struggled to achieve gas–liquid separation with the acceleration below 8.7 × 10−5 m/s2 generated by exhausting. The rotational angular velocity of the tank through exhausting increases with the fill level dropping and exhaust pressure rising. Reorientation by a TVS intermittent exhaust may be possible in some cases, with sufficient exhaust time. This study provides a theoretical basis for reorientation using the exhaust gas of liquid hydrogen.

27 March 2020 in Journal of Low Temperature Physics
Verified
Journal Article
Closed access
PDF file
Yuan MaYuan Ma
Yuan Ma
Yanzhong LiYanzhong Li
Yanzhong Li
Fushou XieFushou Xie
Fushou Xie
JLJian Li
Jian Li
LWLei Wang
Lei Wang

12 May 2018 in Heat and Mass Transfer
Verified
Journal Article
Closed access
PDF file
KZKang Zhu
Kang Zhu
Yanzhong LiYanzhong Li
Yanzhong Li
JWJiaojiao Wang
Jiaojiao Wang
Yuan MaYuan Ma
Yuan Ma
LWLei Wang
Lei Wang
Fushou XieFushou Xie
Fushou Xie