When an induction motor is running at stable speed and low slip, the fault signal of the induction motor’s broken bar faults are easily submerged by the power frequency (50 Hz) signal. Thus, it is difficult to extract fault characteristics. The left-side harmonic component representing the fault characteristics can be distinguished from power frequency owing to V-shaped trajectory of the fault component in time-frequency (t-f) domain during motor startup. This article proposed a scheme to detect broken bar faults and discriminate the severity of faults under starting conditions. In this scheme, successive variable mode decomposition (SVMD) is applied to analyze the stator starting current to extract the fault component, and the signal reconstruction is proposed to maximize the energy of the fault component. Then, the quadratic regression curve method of instantaneous frequency square value of the fault component is utilized to discriminate whether the fault occurs. In addition, according to the feature that the energy of the fault component increases with the fault severity, the energy of the right part of the fault component is proposed to detect the severity of the fault. In this paper, experiments are carried out based on a 5.5 kW three-pole induction motor. The results show that the scheme proposed in this paper can diagnose the broken bar faults and determine the severity of the fault.
23 August 2024 in IEEE Transactions on Industrial Informatics
Past research has shown that completing diagnosis in the incipient fault stage of low-turn, high-resistance short circuits in permanent magnet motors is still a challenge. Meanwhile, the motor signals employed in the established technology route are of poor practicality for motor systems with increasing integration. For these reasons, this article proposes an interturn short-circuit fault diagnosis method utilizing power-side input current and channel attention mechanism. First, this article derives harmonic features of the power-side input current under fault conditions. Then, in order to sufficiently exploit the spatial and temporal scale features of the incipient fault data, this article develops a residual model with an improved channel attention mechanism for interturn short-circuit fault diagnosis. Finally, a 2.3 kW permanent magnet motor has been used for experimental validation. The results show that the fault information can be effectively transmitted to the power-side input current, and the proposed method can accurately diagnose the interturn short-circuit incipient fault. Furthermore, through the feature explainability analysis of the proposed model, this article also finds that the region of the input current fluctuation is favorable for diagnosis and deserves attention.
3 September 2025 in Advanced Engineering Informatics
Servo control systems exhibit strong coupling among multiple control parameters, posing dual challenges of efficiency and stability during optimization. Traditional parameter tuning strategies based on systematic optimization often face difficulties, such as the need for precise modeling, low optimization efficiency, high dependence on data, and structural intrusiveness. This letter rethinks the problem of strongly coupled multiparameter optimization from a feature extraction perspective and proposes a physics-constrained self-supervised optimization framework. By employing a biphase hierarchical encoder and an independent encoder structure, the framework extracts key control parameter features from the system to enable effective optimization of servo control parameters. Furthermore, the method incorporates prior feature knowledge for network preraining, significantly reducing reliance on real data. Experiments conducted under both PI and ADRC control structures demonstrate that the proposed approach achieves rapid error convergence, offering high optimization efficiency while maintaining the structure’s nonintrusiveness.
20 May 2026 in IEEE Transactions on Industrial Electronics
Precise joint position control in tendon-driven dexterous hands with unknown kinematics is challenging due to the difficulty in accurately mapping joint angles to electric cylinder displacement. Furthermore, existing time delay control methods present inherent trade-offs, such as large overshoot due to integral windup in step responses or nonzero steady-state errors during time-varying signals tracking, limited by fixed forgetting factors. To address these issues, this article establishes a dynamically accurate mapping model by lumping hard-to-model parts into an uncertainty term, which is estimated in real time. After analyzing the causes of the limitations of existing methods, an enhanced method incorporating a forgetting factor and a prediction term is proposed, immune to tendon wear and elasticity. The forgetting factor is adjusted automatically to suppress integration during large errors and restore it near steady state, thereby balancing overshoot and accuracy. The prediction term, designed based on the residual error, adds an immediate proportional compensation component that accelerates system response. Then, the compensation mechanism is theoretically analyzed, and parameter tuning guidelines are provided under explicit stability constraints. Comparative experiments on a dexterous hand validate the superiority of the proposed method in achieving low overshoot, short settling time, and high tracking accuracy.
10 October 2025 in IEEE Transactions on Industry Applications
High-performance torque and position control of robots relies on the high-precision current tracking control of joint motors. Among various control methods, time delay control (TDC) has attracted growing interest due to its advantages such as low dependency on parameters, computational simplicity, and good tracking performance for both high- and low-frequency signals. However, existing TDC algorithms for current control lack specificity to robotic operating conditions, and the inherent time delay estimation (TDE) errors reduce the current tracking accuracy. Therefore, this paper proposes a discrete time delay control (DTDC) algorithm with TDE error compensation to achieve higher precision in current tracking control. Firstly, the key factors affecting the current tracking accuracy of joint motors are analyzed based on actual operating conditions. Then, a direct TDE error compensation method is designed from the perspective of gradient descent, and a new DTDC control law is derived based on this, with its stability rigorously proven. Next, the effectiveness of the proposed method is demonstrated through a comparative analysis of transfer functions. Additionally, the direct compensation characteristics of the proposed method are highlighted, followed by the parameter sensitivity analysis and tuning guidelines. Finally, experiments are conducted on a 3.1-kW surface-mounted motor platform and a robotic joint module platform to verify the effectiveness of the proposed DTDC method through comparative analysis.