Techno-economic assessments (TEA) of biodiesel production may comply with various economic and technical uncertainties during the lifespan of the project, resulting in the variation of many parameters associated with biodiesel production, including price of biodiesel, feedstock price, and rate of interest. Engineers may only collect very limited information on these uncertain parameters such as their variation intervals with lower and upper bound. This paper proposes a novel non-probabilistic strategy for uncertainty analysis (UA) in the TEA of biodiesel production with interval parameters, and non-probabilistic reliability index (NPRI) is employed to measure the economically feasible extent of biodiesel production. A sensitivity analysis (SA) indicator is proposed to assess the sensitivity of NPRI with regard to an individual uncertain interval parameter. The optimization method is utilized to solve NPRI and SA. Results show that NPRI in the focused biodiesel production of interest is 0.1211, and price of biodiesel, price of feedstock, and cost of operating can considerably affect TEA of biodiesel production.
The number of fault samples for the new nuclear valve is commonly rare; thus, the machine learning algorithm is not suitable for the fault prediction of this kind of equipment. In order to overcome this difficulty, this paper proposes a novel method for the fault critical point prediction of the gate valve based on the characteristic analysis of the operation process variables. The operation process of gate valve switch often contains various fault characteristics and information, and this method first adopts the Shannon entropy to describe the power spectrum of vibration signal relevant to the operation process of gate valve switch, and then employs the mean value of the power spectrum entropy as an indirect process variable and further investigates the differences between the indirect process variable under the healthy state and the fault state with a different fault degree. In addition, the power signal of the gate valve is also employed as the direct process variable and the features of the direct process variable under the healthy state and the fault state with different fault degrees are also investigated. Based on the previous indirect process variable and direct process variable, the prediction approach for the critical point of the gate valve fault is established by analyzing the change in the indirect process variable and direct process variable before and after faults. Finally, the data of a nuclear gate valve experiment are employed to demonstrate the feasibility of the proposed method and the results show that the proposed method can effectively predict the fault critical point of the mentioned nuclear gate valve. If the diagnostic threshold is set properly, the critical point prediction of a nuclear gate valve fault can be realized as 100% or close to 100%. Furthermore, the proposed method can be directly applied to the nuclear gate valve in a nuclear power plant to improve the operation reliability of the valve. At the same time, the method can be applied to the fault diagnosis and prediction of valves in other fields, such as the chemical industry.
The compressor is a critical component of cryogenic separation industrial systems, and its reliable operation is essential for the stable functioning of the entire system. Existing research focuses on predicting compressor conditions using experimental or simulation data, often neglecting analysis based on actual industrial data. To address this gap, this paper presents an innovative prediction model for compressor data utilizing an LSTM–self-attention mechanism, specifically designed for real industrial systems. The proposed model combines the sequential learning capabilities of LSTM with the dynamic feature extraction strengths of self-attention, enabling highly accurate predictions by enhancing sensitivity to critical data features. The actual vibration data from a compressor spanning 12 months are analyzed and compared. The results demonstrate that the proposed model reduces prediction error by in MSE and in RMSE compared to SVR. These findings highlight the model’s potential for real-time monitoring and early fault detection, providing a robust theoretical foundation for condition-based analysis and preventive maintenance in industrial compressor applications.
Pumped storage power is considered an ideal regulated power source for new energy. However, the traditional one-dimensional characteristic line method cannot predict the pulsating pressure caused by the reverse “S” characteristic of a pump–turbine. In this paper, a variable-step Euler algorithm is presented to calculate the hydraulic transient process of pumped storage units, the interval times of start-up and load regulation between two pump–turbine units are investigated by using the method of peak staggering and valley filling, and the closure law of guide vanes in the transient process of load rejection is optimized. The results show that the presented method is valid, and that pulsating pressure is accurately captured during the transient process of load rejection. The water level fluctuation amplitude in the surge chamber is greatly reduced by the sequential start-up mode. The rotational speed fluctuation amplitude of the sequential load reduction is also reduced. After the load of two pump–turbine units is rejected at the same time, the duration of pulsating pressure in the spiral case is shortened by 45% by using the quick-then-slow closure law compared with the straight-line closure law. Moreover, the pulsating pressure amplitude and the second peak value of rotational speed are also reduced accordingly, and the transient characteristics of the pump–turbine units are greatly improved.
As a key system in nuclear power plants, nuclear power systems contain high-temperature, high-pressure water media. A steam leak, if it occurs, can at minimum cause system functional loss and at worst lead to casualties. Therefore, it is urgent to carry out steam leakage detection work for high-temperature, high-pressure loop systems. Currently, steam leaks are primarily detected through visual monitoring and pressure gauges. However, if there is a minor leak under high system pressure, the slight decrease in pressure may not be enough to alert the operators, leading to a delay in detecting the steam leak. Thus, this detection method has certain drawbacks. In view of these issues, this paper introduces computer vision technology to monitor the high-temperature, high-pressure loop system and proposes the use of an improved background subtraction method to detect steam leaks in the loop system. The results show the following advantages of this method: (1) It can effectively identify steam leaks at an early stage; (2) it overcomes the difficulty of determining the threshold value for the binarization of grayscale images in traditional background subtraction methods; (3) it eliminates the noise impact brought by the binarization of grayscale images in existing improved background subtraction methods. The introduction of this method provides a new approach for detecting steam leaks in high-temperature, high-pressure loop systems and can be effectively applied in engineering fields. It also offers reference value for the detection of high-temperature, high-pressure media leaks in other fields.
Pumped storage power is considered an ideal regulated power source for new energy. However, pulsating pressure caused by the reverse ‘S’ characteristic of pump-turbine has become a hot issue, the traditional one-dimensional characteristic line method cannot predict it. In this paper, a variable step Euler algorithm is presented to calculate the hydraulic transient process of pumped storage units, the interval time of start-up and load regulation between two pump-turbine units are investigated by using the method of peak staggering and valley filling, and the closure law of guide vanes in the transient process of load rejection is optimized. The results show that the presented method is valid, pulsating pressure is accurately captured during the transient process of load rejection. The water level fluctuation amplitude in surge chamber is greatly reduced by the sequential start-up mode; The rotational speed fluctuation amplitude by the sequential load reduction is also reduces; After the load of two pump-turbine units is rejected at the same time, the duration of pulsating pressure in the spiral case is shortened by 45% by using the quick-then-slow closure law compared with the straight-line closure law. Moreover, the pulsating pressure amplitude and the second peak value of rotational speed are also reduced accordingly, and the transient characteristics of the pump-turbine units has been greatly improved.