The electrochemical response of layered lithium transition metal oxides LiMO2 [M=Ni, Mn, Co; e. g., Li(Ni0.5Mn0.3Co0.2)O2 (NMC532)] with single‐crystalline architecture to slow and fast charging protocols and the implication of incomplete and heterogeneous redox reactions on the active material utilization during cycling were the subject of this work. The role of the active material size and the influence of the local microstructural and chemical ramifications in the composite electrode on the evolution of heterogeneous state of charge (SOC) distribution were deciphered. For this, classification‐single‐particle inductively coupled plasma optical emission spectroscopy (CL‐SP‐ICP‐OES) was comprehensively supplemented by various post mortem analytical techniques. The presented results question the impact of surface‐dependent failure mechanisms of single crystals for the evolution of SOC heterogeneity and identify the deficient structural flexibility of the composite electrode framework as the main driver for the observed non‐uniform active material utilization.
Lithium-metal batteries face more challenges than lithium-ion batteries (LIBs) with graphite-based negative electrodes. One significant challenge derives from the highly reactive nature of lithium metal, which can react with electrolytes upon contact to form the solid electrolyte interphase (SEI) and can develop detrimental dendrites upon cycling in contrast to graphite and silicon anodes, which require the application of current/voltage to form the SEI. Studies focusing on lithium metal SEI formation are less frequent than those for other anode materials. Through investigation of several electrolyte formulations including the film forming additives vinylene carbonate (VC) and fluoroethylene carbonate (FEC) we note multiple aspects of their respective SEI formation characteristics, as additives are consumed during interphase formation. Compared to VC, FEC shows a dependency on ethylene carbonate for equivalent interphase formation properties. Amounts of inorganic SEI compounds were found to be lowered after use of additives. Organic electrolyte-soluble compounds were not detectable if the additive is still present. This was achieved through an SEI accumulation process, leading to a sufficient analyte amount and complementary analytical methods ranging from quantitative gas analysis, over qualitative electrolyte analysis using NMR and mass spectrometry and solid residue analysis using XRD and quantitative gas chromatography.
7 January 2026 in Journal of Environmental Management
Inadequate waste management and insufficient environmental standards in lithium ion battery production and recycling pose a substantial risk of environmental pollution. Phytoremediation offers a cost-effective and less-invasive strategy for removing metals from contaminated soils. We evaluated the phytoremediation potential for battery-contaminated soils and enhancement strategies using chelating agents and high-biomass-producing plants. Therefore, metal uptake in Alyssum murale and Brassica juncea was investigated in pot studies with soil amendments of shredded battery material ("black mass") and cathode material (NMC). Alyssum murale effectively accumulated cobalt (832 mg kg-1) and lithium (1044 mg kg-1). Although chelating agents increased metal leachability from the material, only nickel uptake was clearly enhanced by EDTA and EDDS soil amendments. Fast-growing Brassica juncea tolerated high levels of transition metals, while achieving lithium accumulation up to 6082 mg kg-1 and bioaccumulation factors >25 for low-level contaminations. Up to 18.6 % of lithium were removed in a single treatment, corresponding to potential areal yields of 16.4 kg ha-1. However, phytoremediation applications were limited to moderate contamination levels due to phytotoxicity of the battery materials. Overall, Alyssum murale showed strong potential for lithium and cobalt remediation, whereas nickel required mobilization. Brassica juncea proved effectiveness for the extraction of lithium.
Despite large research efforts in the fields of lithium ion and lithium metal batteries, there are still unanswered questions. One of them is the formation of the solid−electrolyte interphase (SEI) in lithium‐metal‐anode‐based battery systems. Until now, a compound profile analysis of the SEI on lithium metal was challenging as the amounts of many compounds after simple contact of lithium metal and the electrolyte were too low for detection with analytical methods. This study presents a novel approach on unravelling the SEI compound profile through accumulation in the gas, liquid electrolyte, and solid phase. The method uses the intrinsic behavior of lithium metal to spontaneously react with the liquid electrolyte. In combination with complementary, state‐of‐the‐art analytical instrumentation and methods, this approach provides qualitative and quantitative results on all three phases revealing the vast variety of compounds formed in carbonate‐based electrolytes.