Xiangrong Zhang

Dr. Xiangrong Zhang

Beijing Institute of Technology, Beijing, China
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 September 2019 in Propellants, Explosives, Pyrotechnics
Verified
Journal Article
Closed access
PDF file
DZDaoli Zhu
Daoli Zhu
LZLin Zhou
Lin Zhou
XZXiangrong Zhang
Xiangrong Zhang

10 April 2017 in Propellants, Explosives, Pyrotechnics
Verified
Journal Article
Closed access
PDF file
DZDaoli Zhu
Daoli Zhu
LZLin Zhou
Lin Zhou
XZXiangrong Zhang
Xiangrong Zhang
JZJiaye Zhao
Jiaye Zhao

20 February 2017 in Propellants, Explosives, Pyrotechnics
Verified
Journal Article
Closed access
PDF file
DLDongwei Li
Dongwei Li
LZLin Zhou
Lin Zhou
XZXiangrong Zhang
Xiangrong Zhang

27 August 2022 in Materials
Verified
Journal Article
Open access
PDF file
HXHanfei Xie
Hanfei Xie
XZXiangrong Zhang
Xiangrong Zhang
FMFeichao Miao
Feichao Miao
TJTao Jiang
Tao Jiang
YZYingzhong Zhu
Yingzhong Zhu
LZLin Zhou
Lin Zhou
When describing the relation between the flow stress and plastic strain of a material under a wide range of strain rates and temperatures, the original Johnson–Cook model generally requires a complicated modification, resulting in a loss of simplicity and clear physical interpretation. In this paper, without modification, the original Johnson–Cook model was calibrated separately for the static and dynamic compression of a DNAN-based melt-cast explosive. The stress–strain curves for static and dynamic compression of this explosive were experimentally measured with a universal testing machine and a split-Hopkinson pressure bar, respectively. Based on the stress–strain curves, the flow stress vs. plastic strain data were extracted and used to calibrate the Johnson–Cook model. The calibration process is described. The parameters for the strain term, strain rate term, and temperature term were fitted sequentially. One set of model parameters was not able to fully describe the relationship between flow stress and plastic strain for both the static and dynamic compression of the DNAN-based melt-cast explosive. Two sets of model parameters were separately calibrated and compared for the static and dynamic compression of this explosive. The effects of the adiabatic temperature rise and the definition of the yield point on this calibration were also investigated.

14 March 2023 in Polymers
Verified
Journal Article
Open access
PDF file
HXHanfei Xie
Hanfei Xie
XZXiangrong Zhang
Xiangrong Zhang
TJTao Jiang
Tao Jiang
YZYingzhong Zhu
Yingzhong Zhu
LZLin Zhou
Lin Zhou
As a matrix for melt-cast explosives, 3,4-dinitropyrazole (DNP) is a promising alternative to 2,4,6-trinitrotoluene (TNT). However, the viscosity of molten DNP is considerably greater compared with that of TNT, thus, requiring the viscosity of DNP-based melt-cast explosive suspensions to be minimized. In this paper, the apparent viscosity of a DNP/HMX (cyclotetramethylenetetranitramine) melt-cast explosive suspension is measured using a Haake Mars III rheometer. Both bimodal and trimodal particle-size distributions are used to minimize the viscosity of this explosive suspension. First, the optimal diameter ratio and mass ratio (two crucial process parameters) between coarse and fine particles are obtained from the bimodal particle-size distribution. Second, based on the optimal diameter ratio and mass ratio, trimodal particle-size distributions are used to further minimize the apparent viscosity of the DNP/HMX melt-cast explosive suspension. Finally, for either the bimodal or trimodal particle-size distribution, if the original data between the apparent viscosity and solid content are normalized, the resultant plot of the relative viscosity versus reduced solid content collapses to a single curve, and the effect of the shear rate on this curve is further investigated.

4 January 2017 in Journal of Energetic Materials
Verified
Journal Article
Closed access
TCTong-Tang Cao
Tong-Tang Cao
LZLin Zhou
Lin Zhou
XZXiangrong Zhang
Xiangrong Zhang
WZWei Zhang
Wei Zhang
FMFeichao Miao
Feichao Miao
Shock sensitivity is one of the key parameters for newly developed, 2,4-dinitroanisole (DNAN)-based, melt-cast explosives. For this paper, a series of shock initiation experiments were conducted using a one-dimensional Lagrangian system with a manganin piezoresistive pressure gauge technique to evaluate the shock sensitivity of an aluminized DNAN/cyclotrimethylenetrinitramine (RDX) melt-cast explosive. This study fully investigated the effects of particle size distributions in both RDX and aluminum, as well as the RDX’s crystal quality on the shock sensitivity of the aluminized DNAN/RDX melt-cast explosive. Ultimately, the shock sensitivity of the aluminized DNAN/RDX melt-cast explosives increases when the particle size decreases in both RDX and aluminum. Additionally, shock sensitivity increases when the RDX’s crystal quality decreases. In order to simulate these effects, an Ignition and Growth (I&G) reactive flow model was calibrated. This calibrated I&G model was able to predict the shock initiation characteristics of the aluminized DNAN/RDX melt-cast explosive.