Power converters with an extended range of line voltage are the main requirement in today's industrial applications like photovoltaic and supercapacitors based energy systems. The variation in the line voltage severely degrades the performance of power converters, because of the extended freewheeling interval, more circulation current, narrow range of zero voltage switching and increased EMI. This work suggests a modified Phase-Shifted Full-Bridge converter that cuts the freewheeling interval and minimizes these problems. It extends the input voltage range by keeping the operational duty cycle of the converter high over the wide range of input voltage while maintaining the performance stable. The proposed converter consists of four low profile transformers having reconfigurable interconnection structure. There are two distinct reconfigurable modes, a series mode and a parallel mode, which can be configured with changes in the operational conditions. The operation of the proposed converter with high switching frequency improves power density. Additionally, the use of multiple transformers minimizes heat management efforts and reduces the overall volume of the converter. The proposed work is validated in hardware characterization for a wide range of input voltage 100-400Vdc and up to the load power of 1kW. The measured energy efficiency of the proposed converter remains stable over the complete range input voltage 100-400Vdc.
48 V is emerging as a safe-to-touch alternative voltage level for electric vehicles (EVs). Using a low- instead of a high-voltage drive train reduces isolation efforts, eliminates the risk of electric shock, and thus increases the system safety. In contrast, fast charging of a 48 V battery would require very high currents and is incompatible with the widely established high-voltage electric vehicle charging infrastructure. Instead of employing additional on board power converters for fast charging, the concept of a reconfigurable battery is presented. A small-scale prototype system is designed consisting of eight 48 V lithium iron phosphate battery modules. In series configuration, they can be charged at 460 V with up to 25 A. In 48 V parallel configuration, the peak discharge current is up to 800 A. The MOSFET-based reconfiguration system also operates as a module charge balancer during high-voltage charging. The cost overhead for the reconfiguration system is estimated to 3% for a scaled-up full size EV. Due to the additional reconfiguration switch resistances, the simulation of a 48 V 75 kW electric vehicle in the World harmonized Light-duty vehicles Test Procedure showed a performance reduction of 0.24%.
The higher switching frequency in combination with di/dt loops and dv/dt nodes in the power stages of high frequency power converters generates higher order harmonics which cause Electro Magnetic Interference (EMI). It is commonly perceived that high frequency converters are more vulnerable to radiated EMI, thus, it is very important to analyze the radiated emission of these converters. According to the author's knowledge, the analysis of the radiated emission of power converters switching in the MHz frequency region has not been presented until now. Therefore, in this paper, the measurements, and analysis of the near field radiated emissions of these emerging power converters is presented. These measurements are beneficial in the early design stage of power converters. Both E-field and H-field and captured and analyzed for a half bridge converter switching at 3 MHz and at the output power level of 25 W. The effects of the magnetic and electric field emissions with the addition of a Y-capacitor and secondary side common mode choke are analyzed.
At present, optical fiber microducts are coupled together by mechanical types of joints. Mechanical joints are thick, require a large space, and reduce the installation distance in multi-microduct installation. They may leak or explode in the blown fiber installation process. Mechanical joints are subjected to time dependent deterioration under long service times beneath the earth’s surface. It may start with a small leakage, followed by damage due to water freezing inside the optical fiber microduct. Optical fiber microducts are made up of high-density polyethylene, which is considered most suitable for thermoelectric welding. For thermoelectric welding of two optical fiber microducts, the welding time should be one second, and should not cause any damage to the inner structure of the microducts that are being coupled. To fulfill these requirements, an LTspice simulation model for the welding system was developed and validated. The developed LTspice model has two parts. The first part models the power input to joule heating wire and the second part models the heat propagation inside the different layers of the optical fiber microduct and surrounding joint by using electro-thermal analogy. In order to validate the simulation results, a battery powered prototype welding system was developed and tested. The prototype welding system consists of a custom-built electrofusion joint and a controller board. A 40 volt 4 ampere-hour Li-Ion battery was used to power the complete system. The power drawn from the battery was controlled by charging and discharging of a capacitor bank, which makes sure that the battery is not overloaded. After successful welding, a pull strength test and an air pressure leakage test were performed to ensure that the welded joints met the requirements set by the mechanical joints. The results show that this new kind of joint and welding system can effectively replace mechanical joints in future optical fiber duct installations.
There is an increasing demand for efficient and low-profile power converters in almost all industrial applications. Some require stable performance over a wide range of input voltages, whereas others require converters with a stable performance over a wide range of output voltages. In this regard, little work has been done to combine both requirements into one solution. This work suggests a unique solution that addresses both requirements at once. A power converter with $2\times 3$ reconfigurable modes has been presented, able to operate with DC gains of 1, 2 and 4, which can be further extended to 8. The converter shows stable performance for the extended range of both input and output voltage. The flexible reconfigurable feature of the proposal can be applied in a variety of applications. Two reconfigurable modes on the input side can be configured following the variation in the line voltage to maintain a stable performance, and three reconfigurable modes for the output voltage, which raises the output voltage from 24V to 48V and 96V. The proposal is applied in an example application of a phase shifted full bridge converter. The converter is characterized for $\text{V}_{\mathrm {in}}=100$ -400V dc , $\text{P}_{\mathrm {out}} =1$ kW.
In this paper, the effect of the core geometry of non-toroidal magnetic cores on the magnetic loss is investigated. A frequency dependent core material-geometry loss factor is developed. This factor is function of the change in the non-toroidal core section and the Steinmetz parameter “β”. In addition, the temperature effect is included in the developed loss model for wide range of frequency and magnetic flux density. The model is applied for ER core and 3C92 ferrite material. The core loss measurements are performed using a Peltier cell. The principle of operation of the Peltier cell is based on the Seebeck effect, which convert the heat flow due to the temperature difference into electric power. The calibration of the Peltier cell is validated with a resistive load and a relative error lower than 1% is achieved. The accuracy of the developed model is assessed with FEA and the experimental results. A maximum error of 10% is registered of the developed core loss model.