Stefan Haller

Dr. Stefan Haller

Department of Electronics Design, Mid Sweden University, Sundsvall, SWEDEN
orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 January 2022 in Electronics
Verified
Journal Article
Open access
PDF file
SHStefan Haller
Stefan Haller
FAfarhan alam
farhan alam
Kent BertilssonKent Bertilsson
Kent Bertilsson
48 V is emerging as a safe-to-touch alternative voltage level for electric vehicles (EVs). Using a low- instead of a high-voltage drive train reduces isolation efforts, eliminates the risk of electric shock, and thus increases the system safety. In contrast, fast charging of a 48 V battery would require very high currents and is incompatible with the widely established high-voltage electric vehicle charging infrastructure. Instead of employing additional on board power converters for fast charging, the concept of a reconfigurable battery is presented. A small-scale prototype system is designed consisting of eight 48 V lithium iron phosphate battery modules. In series configuration, they can be charged at 460 V with up to 25 A. In 48 V parallel configuration, the peak discharge current is up to 800 A. The MOSFET-based reconfiguration system also operates as a module charge balancer during high-voltage charging. The cost overhead for the reconfiguration system is estimated to 3% for a scaled-up full size EV. Due to the additional reconfiguration switch resistances, the simulation of a 48 V 75 kW electric vehicle in the World harmonized Light-duty vehicles Test Procedure showed a performance reduction of 0.24%.

1 November 2015
Verified
Conference Paper
Closed access
SHStefan Haller
Stefan Haller
PCPeng Cheng
Peng Cheng
BOBengt Oelmann
Bengt Oelmann
To verify the FEM simulation of the air-gap flux density, it is necessary to measure the flux density distribution as function of the angular machine position. This paper presents a scalable 3-D direct air-gap flux density magnitude measurement system for rotating electrical machines. A combination of eight linear Hall effect flux sensors and a rotary encoder is used to measure the flux density magnitude as function of the angular machine position. The system is designed for permanent magnet motors with an air gap of at least 1 mm, but can also be used for other types of machines. The miniaturized sensor array with the flux sensors is 0.7 mm thick, and measures the distribution of the air-gap flux density magnitude in a range of ±2 T along the rotor axis. The design of the measurement system is described and tested on a prototype of an electronically commutated permanent magnet DC motor. The obtained measurement results are compared with the FEM simulation results of the prototype motor. A good match between the simulated and measured flux density magnitude is shown. The conclusions presented in this study, are used to further optimize the simulation model and the prototype motor.

1 May 2011
Verified
Conference Paper
Closed access
AMA. Majid
A. Majid
HKH. B. Kotte
H. B. Kotte
JSJ. Saleem
J. Saleem
RAR. Ambatipudi
R. Ambatipudi
SHStefan Haller
Stefan Haller
Kent BertilssonKent Bertilsson
Kent Bertilsson
This paper introduces high frequency half bridge DC-DC converter, using multilayered coreless Printed Circuit Board (PCB) step down power transformer. The converter is simulated and then implemented on a PCB. Complementary Pulse Width Modulated (PWM) signals are generated to turn on high and low side Metal Oxide Semiconductor Field Effect Transistors (MOSFETs) alternately by a micro-controller. The isolated gate drive signals are provided to the high side MOSFET by using high frequency coreless PCB isolation transformer. We tested the converter for switching frequency range of 2 to 3 MHz, and for maximum input voltage up-to 170 V. The maximum output power achieved is 40 W and the maximum energy efficiency is approximately 82%.

23 August 2020
Verified
Conference Paper
Closed access
SHStefan Haller
Stefan Haller
JPJohan Persson
Johan Persson
PCPeng Cheng
Peng Cheng
Kent BertilssonKent Bertilsson
Kent Bertilsson
Traction drive applications demand high power density motors with a good stator cooling design. We propose a novel multi-phase winding for a 48 V traction drive design having identical preformed hollow copper conductors with in-conductor direct cooling capability. This paper studies the cooling performance of an individual conductor phase using either EGW50/50 or water as coolant. Analytical calculations and experiments are conducted on a straight conductor of the same length using 20°C water as coolant. The results are then cross verified with those from the FEM simulations to validate the simulation setup. Then a final simulation is conducted at a current of 700A and a current density of 49.5 $\mathrm{A}/\mathrm{m}\mathrm{m}^{2}$ on the preformed conductor using $65^{\circ}\mathrm{C}\mathrm{E}\mathrm{G}\mathrm{W}50/50$ as coolant at a pressure of $140\mathrm{k}\mathrm{P}\mathrm{a}$. The results highlight the exceptional performance of the cooling design which enables a power dissipation of 71OW at a maximum conductor temperature rise of only 56. $9^{\circ}\mathrm{C}$.

28 July 2020 in International Journal of Electronics
Verified
Journal Article
Open access
MBMuhammad Abu Bakar
Muhammad Abu Bakar
SHStefan Haller
Stefan Haller
Kent BertilssonKent Bertilsson
Kent Bertilsson
To execute soft switching methods in resonant power converters, transformers with larger leakage inductance are getting more attention. Many papers have constructed various concepts in this regard. However, a discussion about, how the transformer efficiency is affected is lacking in the literature. This paper analyses the effects of the increased leakage inductance on the performance of the transformer. A transformer for increased leakage inductance is modelled and constructed to investigate the losses. The model discusses the effects of increased leakage inductance either by increasing the inter-winding spacing or by integrating the magnetic shunt within the transformer. The investigations show that increasing the leakage inductance by inserting a magnetic shunt can have severe degrading effects on the performance of the transformer, if not designed adequately. Additional losses are also calculated and the effects are verified by the experiments.

1 October 2016
Verified
Conference Paper
Closed access
SHStefan Haller
Stefan Haller
PCPeng Cheng
Peng Cheng
BOBengt Oelmann
Bengt Oelmann
Rapid development of extremely-low voltage high current MOSFETs allows reversing common design principles to explore new applications, such as battery powered traction drives. This enables the usage of multi-phase single-turn stator windings which can achieve a copper fill factor close to one. This paper briefly describes the proposed 2V, 1.1kW MOSFET commutated 13-phase permanent magnet DC motor and presents the efficiency and resistive loss measurements of the first prototype. The motor was successfully run with drive currents up to 520 A. Most of the obtained losses were resistive contact losses due to the flexible winding connections, less than 6% are dedicated to the MOSFETs. The results show that such a high current drive system is feasible and has great potential for further improvements, which is supported by the rapid development of extremely-low voltage high current semiconductors.