Ioana Monica Sas-Boca

Mrs. Ioana Monica Sas-Boca

Materials Science and Engineering Department, Technical University of Cluj-Napoca, Cluj-Napoca, Cluj, Romania
orcid
Lecturer, Materials Science and Engineering Department, Te...

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2017 in Procedia Engineering
Verified
Journal Article
Open access
Ioana Monica Sas-BocaIoana Monica Sas-Boca
Ioana Monica Sas-Boca
MTMarius Tintelecan
Marius Tintelecan
MPMariana Pop
Mariana Pop
DIDana-Adriana Iluţiu-Varvara
Dana-Adriana Iluţiu-Varvara
AMAdriana Maria Mihu
Adriana Maria Mihu

1 January 2017 in Procedia Engineering
Verified
Journal Article
Open access
MTMarius Tintelecan
Marius Tintelecan
Ioana Monica Sas-BocaIoana Monica Sas-Boca
Ioana Monica Sas-Boca
DIDana-Adriana Iluţiu-Varvara
Dana-Adriana Iluţiu-Varvara

1 January 2020 in Procedia Manufacturing
Verified
Journal Article
Open access
DVDana - Adriana Iluțiu - Varvara
Dana - Adriana Iluțiu - Varvara
CAClaudiu Aciu
Claudiu Aciu
MTMarius Tintelecan
Marius Tintelecan
Ioana Monica Sas-BocaIoana Monica Sas-Boca
Ioana Monica Sas-Boca

9 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
Ioana Monica Sas-BocaIoana Monica Sas-Boca
Ioana Monica Sas-Boca
Ilutiu-Varvara Dana AdrianaIlutiu-Varvara Dana Adriana
Ilutiu-Varvara Dana Adriana
TMTintelecan Marius
Tintelecan Marius
CLAUDIU ACIUCLAUDIU ACIU
CLAUDIU ACIU
DFDan Ioan Frunza
Dan Ioan Frunza
FPFlorin Popa
Florin Popa
Through the approaches in this article, an attempt was made to analyze the bonding of Al-Cu bimetallic composite layers and the highlight of the diffusion at the boundary between the layers, by hot rolling. An aluminum alloy 6060 plate (EN-AW AlMgSi) and a Cu-ETP ½ hard (CW004A) plate were used. All of these layers of materials were TIG-welded, at both ends, into a heat-treated layered composite and subsequently subjected to the hot-rolling process. The Al-Cu composite material obtained was analyzed by scanning electronic microscopy (SEM) analysis, after being subjected to the tensile test, as well as energy-dispersive X-ray (EDX) analysis. The obtained results highlighted the diffusion at the boundary between the layers of the Al-Cu composite as well as its ductile breakage and the distribution of the amount of Al and Cu at the interface of the layers.

1 January 2015 in Procedia Technology
Verified
Journal Article
Open access
DIDana-Adriana Iluţiu-Varvara
Dana-Adriana Iluţiu-Varvara
CMCarmen Maria Mârza
Carmen Maria Mârza
Ioana Monica Sas-BocaIoana Monica Sas-Boca
Ioana Monica Sas-Boca
VCVasile Adrian Ceclan
Vasile Adrian Ceclan
Carbon oxides (COx) have a negative impact on the steelworkers, environment and populations. The aim of this paper is to assess the COx emissions from steelmaking in the electric arc furnaces, in order to improve the gaseous emissions management, an essential factor for sustainable development, by identifying the most polluting technological stages of this process. The experimental researches were carried out on two electric arc furnaces with alkaline lining. The measurement of COx emissions was performed using a Maxilyzer computer for burned gases automated analysis. After evaluating the emissions of COx during steelmaking in electric arc furnaces, it results that: the most significant emissions have been generated at the end of the melting and refining stage; in terms of pollution by COx, the most polluting stages are melting and refining; the level of COx emissions from electric arc furnaces depends on the carbon content of material input. The reduction of COx emissions to the steelmaking in the electric arc furnaces is possible by charge component selection and by the use of raw materials with reduced carbon content

1 March 2023 in Materials
Verified
Journal Article
Open access
PDF file
MPMariana Pop
Mariana Pop
ANAdriana NEAG
Adriana NEAG
Ioana Monica Sas-BocaIoana Monica Sas-Boca
Ioana Monica Sas-Boca
The aim of this manuscript is the experimental and numerical study regarding the influence of friction conditions on plastic deformation behavior by upsetting the A6082 aluminum alloy. The upsetting operation is characteristic of a significant number of metal forming processes: close die forging, open die forging, extrusion, and rolling. The purpose of the experimental tests was to determine: by the ring compression method, the friction coefficient for 3 surface lubrication conditions (dry, mineral oil, graphite in oil) by using the Coulomb friction model; the influence of strains on the friction coefficient; the influence of friction conditions on the formability of the A6082 aluminum alloy upsetted on hammer; study of non-uniformity of strains in upsetting by measuring hardness; change of the tool-sample contact surface and non-uniformity of strains distribution in a material by numerical simulation. Regarding the tribological studies involving numerical simulations on the deformation of metals, they mainly focused on the development of friction models that characterize the friction at the tool-sample interface. The software used for the numerical analysis was Forge@ from Transvalor.