Ioana Monica Sas-Boca

Mrs. Ioana Monica Sas-Boca

Materials Science and Engineering Department, Technical University of Cluj-Napoca, Cluj-Napoca, Cluj, Romania
orcid
Lecturer, Materials Science and Engineering Department, Te...

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2017 in Procedia Engineering
Verified
Journal Article
Open access
Ioana Monica Sas-BocaIoana Monica Sas-Boca
Ioana Monica Sas-Boca
MTMarius Tintelecan
Marius Tintelecan
MPMariana Pop
Mariana Pop
DIDana-Adriana Iluţiu-Varvara
Dana-Adriana Iluţiu-Varvara
AMAdriana Maria Mihu
Adriana Maria Mihu

1 January 2017 in Procedia Engineering
Verified
Journal Article
Open access
MTMarius Tintelecan
Marius Tintelecan
Ioana Monica Sas-BocaIoana Monica Sas-Boca
Ioana Monica Sas-Boca
DIDana-Adriana Iluţiu-Varvara
Dana-Adriana Iluţiu-Varvara

1 January 2020 in Procedia Manufacturing
Verified
Journal Article
Open access
DVDana - Adriana Iluțiu - Varvara
Dana - Adriana Iluțiu - Varvara
CAClaudiu Aciu
Claudiu Aciu
MTMarius Tintelecan
Marius Tintelecan
Ioana Monica Sas-BocaIoana Monica Sas-Boca
Ioana Monica Sas-Boca

9 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
Ioana Monica Sas-BocaIoana Monica Sas-Boca
Ioana Monica Sas-Boca
Ilutiu-Varvara Dana AdrianaIlutiu-Varvara Dana Adriana
Ilutiu-Varvara Dana Adriana
TMTintelecan Marius
Tintelecan Marius
CLAUDIU ACIUCLAUDIU ACIU
CLAUDIU ACIU
DFDan Ioan Frunza
Dan Ioan Frunza
FPFlorin Popa
Florin Popa
Through the approaches in this article, an attempt was made to analyze the bonding of Al-Cu bimetallic composite layers and the highlight of the diffusion at the boundary between the layers, by hot rolling. An aluminum alloy 6060 plate (EN-AW AlMgSi) and a Cu-ETP ½ hard (CW004A) plate were used. All of these layers of materials were TIG-welded, at both ends, into a heat-treated layered composite and subsequently subjected to the hot-rolling process. The Al-Cu composite material obtained was analyzed by scanning electronic microscopy (SEM) analysis, after being subjected to the tensile test, as well as energy-dispersive X-ray (EDX) analysis. The obtained results highlighted the diffusion at the boundary between the layers of the Al-Cu composite as well as its ductile breakage and the distribution of the amount of Al and Cu at the interface of the layers.

1 January 2015 in Procedia Technology
Verified
Journal Article
Open access
DIDana-Adriana Iluţiu-Varvara
Dana-Adriana Iluţiu-Varvara
CMCarmen Maria Mârza
Carmen Maria Mârza
Ioana Monica Sas-BocaIoana Monica Sas-Boca
Ioana Monica Sas-Boca
VCVasile Adrian Ceclan
Vasile Adrian Ceclan
Carbon oxides (COx) have a negative impact on the steelworkers, environment and populations. The aim of this paper is to assess the COx emissions from steelmaking in the electric arc furnaces, in order to improve the gaseous emissions management, an essential factor for sustainable development, by identifying the most polluting technological stages of this process. The experimental researches were carried out on two electric arc furnaces with alkaline lining. The measurement of COx emissions was performed using a Maxilyzer computer for burned gases automated analysis. After evaluating the emissions of COx during steelmaking in electric arc furnaces, it results that: the most significant emissions have been generated at the end of the melting and refining stage; in terms of pollution by COx, the most polluting stages are melting and refining; the level of COx emissions from electric arc furnaces depends on the carbon content of material input. The reduction of COx emissions to the steelmaking in the electric arc furnaces is possible by charge component selection and by the use of raw materials with reduced carbon content

29 May 2024 in Metals
Verified
Journal Article
Open access
PDF file
MPMariana Pop
Mariana Pop
Ioana Monica Sas-BocaIoana Monica Sas-Boca
Ioana Monica Sas-Boca
DFDan Ioan Frunza
Dan Ioan Frunza
FPFlorin Popa
Florin Popa
ANAdriana NEAG
Adriana NEAG
The influence of elevated temperatures and strain rate on the mechanical and structural properties of steel 42CrMo4 were analysed experimentally in this paper. The experiments were based on uniaxial tension and compression tests at high temperatures between 700 °C and 1100 °C and strain rates in the range 0.0018–0.1 s−1. The influence of temperature and strain rate on yield stress, strain to fracture, hardness, structural changes, and fracture characteristics were analysed. The non-uniformity of deformations obtained at different values of the strain rate and temperature were also analysed. Analysis by scanning electron microscopy showed the ductile behaviour of the material. The degree of damage in the material caused by the presence of cavities increased with increasing deformation temperature. For all the presented deformation conditions, the formation of the fracture through the ductile fracture mechanism resulted from localized necking and the coalescence of microvoids. By increasing the deformation temperature and reducing the strain rate, the fracture behaviour of 42CrMo4 steel can be improved.