Sheila Medeiros de Carvalho

Dr. Sheila Medeiros de Carvalho

Department of Mechanical Engineering, Federal University of Espirito Santo, Av. Fernando Ferrari, 514, Vitória 29075-910, ES, Brazil

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 January 2026 in Lasers in Manufacturing and Materials Processing
Verified
Journal Article
Open access
PDF file
GZGabriela Lugão de Souza Zatta
Gabriela Lugão de Souza Zatta
OLOlga Liskevych
Olga Liskevych
Milton Sergio Fernandes de LimaMilton Sergio Fernandes de Lima
Milton Sergio Fernandes de Lima
RSRafael Siqueira
Rafael Siqueira
Diego CelentanoDiego Celentano
Diego Celentano
SCSheila Medeiros de Carvalho
Sheila Medeiros de Carvalho
Laser beam forming is a non-contact process that uses a laser beam as a heat source to deform components. In this study, the microstructural and mechanical aspects of an aluminum sheet of class AA6013-T4 were studied after shaping using a fiber laser. The surfaces of the aluminum plates were coated with graphite to increase their absorptivity. Under the conditions of 200 W power, treatment speed of 3 mm/s, and focal diameter of 0.5 mm on the surface of the plate, one to three runs were performed for each sample. The width and depth of the remelted lines did not vary significantly with the number of runs, whereas the in-depth hardness profile tended to become uniform as the number of irradiation cycles increased. This study indicated a tendency towards tensile (positive) residual stress in both the longitudinal and transverse directions, with relaxation in the free part of the sheet. These components have been associated with bending angles ranging from 0.04 to 0.13 rad, depending on the number of laser runs. The maximum tensile stresses measured in the fusion zone, which was transversal to the laser path, were approximately 100 MPa, independent of the number of runs.

21 February 2021 in Metals
Verified
Journal Article
Open access
PDF file
EREsteban Ramos-Moore
Esteban Ramos-Moore
JHJoaquin Hoffmann
Joaquin Hoffmann
RSRafael Siqueira
Rafael Siqueira
SCSheila Medeiros de Carvalho
Sheila Medeiros de Carvalho
Milton Sergio Fernandes de LimaMilton Sergio Fernandes de Lima
Milton Sergio Fernandes de Lima
Diego CelentanoDiego Celentano
Diego Celentano
The aim of this work is the analysis of laser beam forming (LBF) in the bending of two relevant materials used in the transportation industry—interstitial-free (IF) steel and AA6013 high-strength aluminum alloy. Our experiments and numerical simulations consider two different operating scenarios achieved by varying the laser beam scanning velocity using linear paths. The material behavior during this process is described via a coupled thermomechanical-plasticity-based formulation that allows prediction of temperature profiles and bending angles. Metallography, glow discharge optical emission spectroscopy, and X-ray diffraction are used for microstructure characterization. In addition, microstress analyses are performed in order to study the stress behavior of the irradiated zones. It is found that LBF mainly induces grain growth and melting in the case of high surface temperatures. Before melting, the materials developed compressive stresses that could be useful in preventing cracking failures. The resulting bending angles are predicted and experimentally validated, indicating the robustness of the model to estimate LBF effects on advanced alloys. The present analysis relating bending angles together with temperature and microstructure profiles along the thickness of the sheets is the main original contribution of this work, highlighting the need for further modeling refinement of the effects of LBF on advanced alloys to include more microstructural properties, such as grain boundary diffusion and surface roughness.

30 October 2026 in Iron
Verified
Journal Article
Open access
PDF file
Milton Sergio Fernandes de LimaMilton Sergio Fernandes de Lima
Milton Sergio Fernandes de Lima
SCSheila Medeiros de Carvalho
Sheila Medeiros de Carvalho
RSRafael Siqueira
Rafael Siqueira
This study develops and critically assesses a modified flash-laser method for estimating, in a single arrangement, the effective thermal diffusivity and the effective near-infrared laser absorptivity of a bulk (8-mm-thick) 310S austenitic stainless steel block. Samples were irradiated with a defocused, continuous-wave ytterbium fiber laser, while thermocouples monitored the rear-face temperature response. Thermal diffusivity was estimated by fitting the normalized transient temperature curves as a function of time, whereas absorptivity was calculated using a calorimetric approach based on the measured temperature rise and the delivered laser energy. The mean thermal diffusivity obtained from nine measurements was α = (2.6 ± 0.1) × 10−6 m2/s, with acceptable fitting quality and moderate replicate scatter. This value is approximately 25% lower than handbook values for austenitic stainless steels. Three-dimensional simulations show that beam non-uniformity, heat losses, and the finite response time of the contact thermocouple bias the one-dimensional estimate by a comparable amount; the diffusivity is therefore reported as an effective, configuration-specific value. The mean effective absorptivity at 1070 nm was A = 0.30 ± 0.04 (mean ± standard deviation; expanded uncertainty of a single determination ±0.05, dominated by the manually controlled irradiation time), with improved repeatability at fixed delivered energy. This value agrees well with reported calorimetric absorptivities for metallic alloys irradiated with near-infrared lasers. The results apply to ground surfaces near room temperature (rear-face temperatures below 60 °C), and the analysis identifies the improvements needed for the method to deliver intrinsic property values.