Room‐temperature (RT) gas sensitivity of morphology‐controlled free‐standing hollow aluminum‐doped zinc oxide (AZO) nanofibers for NO2 gas sensors is presented. The free‐standing hollow nanofibers are fabricated using a polyvinylpyrrolidone fiber template electrospun on a copper electrode frame followed by radio‐frequency sputtering of an AZO thin overlayer and heat treatment at 400 °C to burn off the polymer template. The thickness of the AZO layer is controlled by the deposition time. The gas sensor based on the hollow nanofibers demonstrates fully recoverable n‐type RT sensing of low concentrations of NO2 (0.5 ppm). A gas sensor fabricated with Al2O3‐filled AZO nanofibers exhibits no gas sensitivity below 75 °C. The gas sensitivity of a sensor is determined by the density of molecules above the minimum energy for adsorption, collision frequency of gas molecules with the surface, and available adsorption sites. Based on finite‐difference time‐domain simulations, the RT sensitivity of hollow nanofiber sensors is ascribed to the ten times higher collision frequency of NO2 molecules confined inside the fiber compared to the outer surface, as well as twice the surface area of hollow nanofibers compared to the filled ones. This approach might lead to the realization of RT sensitive gas sensors with 1D nanostructures.
Poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) is one of the most promising candidate materials for flexible thermoelectric generators. We report changes in morphological, electrical, and thermoelectric properties of strained PEDOT:PSS thin films treated with solvents, including H2SO4, MeOH, and polyethylene glycol (PEG). The stretching creates macroscopic cracks on the thin film surface and microscopically change the domain structure from a dense network to an isolated state. With increasing strain, short, fine cracks at small strains propagate into long, thick cracks. The H2SO4 treatment makes PEDOT:PSS very brittle even at ∼5% strain, whereas PEG improves the stretchability of PEDOT:PSS up to 50%. Stretching reduces the electrical conductivity of solvent-treated samples, which agrees well with the decreased hole concentration of strained PEDOT:PSS, as confirmed by ultraviolet photoemission spectroscopy. In contrast, the Seebeck coefficient (S) of the strained PEDOT:PSS thin films increases. The PEG sample shows the highest S, and thus exhibits an enhanced power factor (PF) with strain, while other solvent treatments reduce PF. To the best of our knowledge, this is the first report on the strain-induced enhancement of S and thermoelectric PF of PEDOT:PSS.
Transparent solar cells (TSCs) are emerging devices that combine the advantages of visible transparency and light-to-electricity conversion. Currently, existing TSCs are based predominantly on organics, dyes, and perovskites; however, the rigidity and color-tinted transparent nature of those devices strongly limit the utility of the resulting TSCs for real-world applications. Here, we demonstrate a flexible, color-neutral, and high-efficiency TSC based on a freestanding form of n-silicon microwires (SiMWs). Flat-tip SiMWs with controllable spacing are fabricated via deep-reactive ion etching and embedded in a freestanding transparent polymer matrix. The light transmittance can be tuned from ~10 to 55% by adjusting the spacing between the microwires. For TSCs, a heterojunction is formed with a p-type polymer in the top portion of the n-type flat-tip SiMWs. Ohmic contact with an indium-doped ZnO film occurs at the bottom, and the side surface has an Al2O3 passivation layer. Furthermore, slanted-tip SiMWs are developed by a novel solvent-assisted wet etching method to manipulate light absorption. Finite-difference time-domain simulation revealed that the reflected light from slanted-tip SiMWs helps light-matter interactions in adjacent microwires. The TSC based on the slanted-tip SiMWs demonstrates 8% efficiency at a visible transparency of 10% with flexibility. This efficiency is the highest among Si-based TSCs and comparable with that of state-of-the-art neutral-color TSCs based on organic–inorganic hybrid perovskite and organics. Moreover, unlike others, the stretchable and transparent platform in this study is promising for future TSCs.