In this paper, the effect of different shapes of tool pin on the plastic flow of 2024-T6 aluminum alloy during friction stir welding was studied. In order to observe the plastic flow of materials more clearly, we chose the method of friction stir welding of dissimilar materials, considering the different corrosive characteristics of aluminum alloys made of different materials when exposed to the same corrosive liquid. By studying and comparing the temperature field, macro and microstructure, microhardness and tensile properties of welded joints, the results indicated that the metal in the weld nugget zone (WNZ) mainly came from the base metal of the advancing side, the thread being the driving force of the downward movement of the FSW plastic metal. The deep groove thread tool pin had the strongest ability to drive the metal downward. The conical cam thread tool pin had the strongest stirring effect on materials and the best metal fluidity. The macroscopic morphology, microstructure, mechanical properties and fracture morphology of different joints were analyzed, and the results showed that all joints could form an excellent union, with an onion ring pattern appearing in cross-section. The minimum grain size of the WNZ formed by the conical cam thread stirring head was 7~12 μm; the hardness was least at the junction of the heat affected zone (HAZ) and the thermo-mechanically affected zone (TMAZ). However, the hardness of the weld formed by the conical cam thread at this point was higher than that of other stirring heads; the tensile strength of all joints was more than 80% of the BM, and the maximum tensile strength of the joint welded by the conical cam thread tool pin was 364.27 MPa, accounting for 86.73% of the base metal (BM). The elongation after break was 14.95%. Tensile fracture morphology analysis showed that all joints were fractured by plastic fracture.

Over the last 20 years, industry interest in copper has increased. Its application in the petrochemical, automotive, and nuclear power industries highlights the need for new research directions especially in the joining of copper to other metals. In this work, lap joint of 304 stainless steel and T2 copper precoated with Cu–Mn–Ni filler metal was performed by laser brazing. The aim of this study is to characterize the influence of laser beam incidence angle on the welded joint forming mode, microstructure, elements diffusion and corrosion resistance. According to the findings, the joint is classified as a welded joint when the laser beam incidence angle is 80°, and as a welded-brazed joint when it’s 90°, 70°, or 60°. The microstructure is mainly composed of Cu-rich and Fe-rich phases, Mn in the Cu-rich phase aggregation and Cr in the Fe-rich phase aggregation. In the fusion zone (FZ) the content of less than 50% of the liquid will be in the form of supersaturated droplets in the matrix of the other side. The local corrosion pair that the copper steel matrix and liquid drop produce in the FZ speeds up the dissolution of the Cu-rich phase, which effected corrosion resistance of the joint.

In this paper, the butt joint of unequal thickness 410 ferritic stainless steel and RCL540 low-carbon alloy steel sheets are realized by laser welding. The effects of different laser powers on weld formability, mechanical properties, and residual stress in the welding process are investigated. It is observed that with increasing laser power, the heat accumulates at the bottom of the molten pool and weld metal, causing the ratios of upper and lower melt widths to decrease. The tensile test results show that all specimens fractured in the weak zone of the base metal on the stainless steel side at 10 mm from the weld seam. The residual stress distributions of the specimens are calculated using ABAQUS 2022 software and compared with the measurements of the blind-hole method. It is found that the stainless steel side produces tensile stresses, with the power increase offset by compressive stresses in the base metal. When the laser power is 1200 W, the welded joint has the best weld formability and mechanical properties and the least residual stress. The upper and lower melt width ratio is 1.17, the maximum microhardness of the weld metal is 374.7 HV, the maximum test force and tensile strength are 5617.5 N and 468.12 MPa, respectively, and the minimum values of the transverse and longitudinal stresses are −45.8 MPa and −106.4 MPa, respectively.