Ice accretion on aircrafts or their engines can cause serious problems and even accidents. Traditional anti-icing and de-icing systems reduce engine efficiency, which can be improved by the use of hydrophobic/icephobic coatings or surfaces that reduce the amount of bleed air or electric power needed. These hydrophobic/icephobic coatings or surfaces are eroded by high-speed air flow, water droplets, ice crystals, sand, and volcanic ash, resulting in the degradation, material loss, or deterioration of the coating’s waterproof and anti-icing properties. Thus, the durability of hydrophobic micro/nanostructured surfaces is a major concern in aircraft applications. However, the mechanism responsible for material loss in hydrophobic micro/nanostructured surfaces resulting from high-speed erosion remains unclear. In this paper, hydrophobic titanium alloy surfaces with cubic pit arrays are fabricated by photoetching and tested using a high-speed sand erosion rig. Under the same impact conditions, the erosion rates of the micro/nanostructured titanium surfaces were similar to those of smooth titanium alloy, implying that the hydrophobic surface fabricated on the bulk material had erosion-resistant capabilities. The material loss mechanisms of the micro/nanostructures under different impact angles were compared, providing useful information for the future optimization of micro/nanostructures with the goal of improved erosion resistance.
The vibration characteristics of a composite fan blade are much more complex than those of a solid titanium fan blade due to the anisotropic material properties and complex excitations coming from unsteady flow and mechanically induced vibration. In this study, the dynamic response measurement of a wide-chord composite fan blade was carried out to study the vibration characteristics using multiple macro fiber composite (MFC) actuators, which can generate complex excitation forces with different frequencies and peak values at different locations. The measured mode shapes and natural frequencies were compared with the finite element simulation results. Based on these results, the responses of the blade under the instantaneous excitation of three MFC actuators with different combinations of several natural frequencies were measured and compared. The results show that the responses of the blade excited by different combinations of MFC actuators with different frequencies were significantly different from those excited by a single MFC actuator. The superposition of different mode shapes may cause the change of the vibration stress state, which indicates that the high cycle fatigue location of the blade under complex excitations may change to an unexpected location. The results will be helpful in understanding the vibration characteristics of the composite blades under complex excitations, and the MFC actuator could be a potential tool in vibration active control.
This paper explores the windmilling operational boundary and aerodynamic characteristics of an axial wide-chord fan rotor according to the zero-torque characteristic. The interesting results show the radial profiles of the aerodynamic parameters at the rotor exit nearly collapse to the same curve for different windmilling speeds, which indicate that windmilling flow has a strong similarity. Meanwhile, there are three different operating modes along the blade span. The formation mechanism and evolution process of the tip leakage flow at the windmill are also analyzed. The reversal of the pressure difference will generate two kinds of tip leakage flows in opposite directions. A clear blockage zone appears near the blade tip under the joint action of the two kinds of tip leakage flows. Finally, this study proposes a mathematical model to predict the windmilling speed of a high-bypass-ratio turbofan based on the aerodynamic similarity of windmilling flow and the one-dimensional semiempirical windmilling mass flow function. This can be applied to the early stages of high-bypass-ratio turbofan development and can evaluate safety characteristics during engine windmilling operations.
In order to study the evolution process and hydraulic characteristics of pressurizer insurge in CPR1000 pressurized water reactor (PWR), the computational fluid dynamics (CFD) of three-dimensional unsteady heat transfer was used to capture the temperature and velocity fluctuation intensity of the mixing of the hot and cold. The results show that Realizable k–ε Turbulence Model combined with VOF multiphase heat transfer model can effectively predict the development trend of pressurizer insurge process. The small diameter pressurizer surge line of CPR1000 enhances the intensity of velocity fluctuation. From the essence of flow and heat transfer, it is concluded that buoyancy force can increase the degree of fluctuation and make an accelerated effect on the influx cold fluid. The electric heater inside the pressurizer should be arranged as far as possible in z<-0.45m and z>0.45m; it is beneficial to improve its harsh operating environment. This research can provide reference for the structural design of pressurizer and the layout optimization of the electric heater.