Blade tip timing (BTT) data are usually an under-sampled signal and are vulnerable to noise and sensor failures. In this paper, based on an arbitrary-angle compressed-sensing method and equiangular tight frame theory, combined with a niching microgenetic algorithm, a method for placing BTT sensors is proposed to ensure higher reconstruction accuracy and reliability. If the dimensions of the sensing matrix are moderate, the index range of arrangements with excellent performance in multifrequency signal reconstruction is determined by enumerating all the uniform-distribution extraction placements. A two-parameter search method is then proposed. Reconstruction of a mixed-signal is carried out to verify the asynchronous signal-reconstruction performance. Thus, to achieve a larger frequency multiplication recognition range and probe-installation flexibility, a method for optimizing the BTT sensor placement is proposed. Finally, a finite-element simulation of the signal from an aero-engine fan blade is used to verify the reconstruction ability of the proposed method. The results show that the placement determined by the optimization algorithm can achieve similar or even better performance than the optimal placement under uniform distribution extraction. The proposed sensor-placement optimization method has a high reconstruction success rate and the BTT system is robust. This approach has significant value for engineering applications.
Ice accretion on aircrafts or their engines can cause serious problems and even accidents. Traditional anti-icing and de-icing systems reduce engine efficiency, which can be improved by the use of hydrophobic/icephobic coatings or surfaces that reduce the amount of bleed air or electric power needed. These hydrophobic/icephobic coatings or surfaces are eroded by high-speed air flow, water droplets, ice crystals, sand, and volcanic ash, resulting in the degradation, material loss, or deterioration of the coating’s waterproof and anti-icing properties. Thus, the durability of hydrophobic micro/nanostructured surfaces is a major concern in aircraft applications. However, the mechanism responsible for material loss in hydrophobic micro/nanostructured surfaces resulting from high-speed erosion remains unclear. In this paper, hydrophobic titanium alloy surfaces with cubic pit arrays are fabricated by photoetching and tested using a high-speed sand erosion rig. Under the same impact conditions, the erosion rates of the micro/nanostructured titanium surfaces were similar to those of smooth titanium alloy, implying that the hydrophobic surface fabricated on the bulk material had erosion-resistant capabilities. The material loss mechanisms of the micro/nanostructures under different impact angles were compared, providing useful information for the future optimization of micro/nanostructures with the goal of improved erosion resistance.
The vibration characteristics of a composite fan blade are much more complex than those of a solid titanium fan blade due to the anisotropic material properties and complex excitations coming from unsteady flow and mechanically induced vibration. In this study, the dynamic response measurement of a wide-chord composite fan blade was carried out to study the vibration characteristics using multiple macro fiber composite (MFC) actuators, which can generate complex excitation forces with different frequencies and peak values at different locations. The measured mode shapes and natural frequencies were compared with the finite element simulation results. Based on these results, the responses of the blade under the instantaneous excitation of three MFC actuators with different combinations of several natural frequencies were measured and compared. The results show that the responses of the blade excited by different combinations of MFC actuators with different frequencies were significantly different from those excited by a single MFC actuator. The superposition of different mode shapes may cause the change of the vibration stress state, which indicates that the high cycle fatigue location of the blade under complex excitations may change to an unexpected location. The results will be helpful in understanding the vibration characteristics of the composite blades under complex excitations, and the MFC actuator could be a potential tool in vibration active control.
29 April 2019 in Journal of Vibration Engineering & Technologies
Blade Tip Timing (BTT) is a promising method to measure the vibration of rotating blades by installing probes on the casing. The Zablotsky-Korostelev Single Parameter Technique (SPT) is widely used to identify the vibrational characteristics of blade synchronous responses. This method assumes that the influence of blade’s own vibration on arrival time can be neglected. However, it is reported that vibrations of rotating blades with large amplitudes will cause errors in identifying maximum vibration amplitude because of the above-mentioned assumption. In this paper, we derived a mathematical model of single degree of freedom (SDOF) blade model discarding the assumption of small amplitude related to BTT actual measurement. Compared to traditional SPT, our model takes the influence of blade’s own vibration into consideration. Then, we improved SPT and derived a precise measurement formula. Arrival time of blade to the sensor was revised. Based on this, we conducted a parametrical study on the effects of changes in various factors including excitation force, damping ratio, engine order, and the installation position of the sensor by numerical simulations. Displacements between considering blade’s own vibration and not were compared. Errors in fitted parameters were also analyzed. The numerical simulation results show that large engine order will magnify the error in fitted parameters if traditional SPT was used. Damping ratio and maximum vibration amplitude have relatively large errors in fitting parameters. Furthermore, we designed an experimental bench to verify the mathematical model and the revised measurement formula.