Jingran Zhang

Dr. Jingran Zhang


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 September 2022 in Journal of Environmental Chemical Engineering
Verified
Journal Article
Closed access
SHShan Huang
Shan Huang
JZJingran Zhang
Jingran Zhang
CWChuqiao Wang
Chuqiao Wang
Guangcan ZhuGuangcan Zhu
Guangcan Zhu
MHMahdi Hassan
Mahdi Hassan

14 April 2022 in Langmuir
Verified
Journal Article
Closed access
JZJingran Zhang
Jingran Zhang
YWYu Wang
Yu Wang
XZXinming Zhang
Xinming Zhang
WXWenkun Xie
Wenkun Xie
JLJing Li
Jing Li
ZWzuobin wang
zuobin wang

19 October 2020 in Analytical Methods
Verified
Journal Article
Closed access
PDF file
TJTuoyu Ju
Tuoyu Ju
SWShuwei Wang
Shuwei Wang
JWJiajia Wang
Jiajia Wang
FYFan Yang
Fan Yang
ZSZhengxun Song
Zhengxun Song
ZWzuobin wang
zuobin wang
Tumor-derived exosomes (exos) are closely related to the occurrence, development and treatment of tumors. However, it is not clear how the exosomes affect the physical properties, which lead to the deterioration of the target cells. In this paper, atomic force microscopy (AFM) was used to study the effects of exosomes in HCC-LM3 cells and other cells (SMMC-7721 and HL-7702). The results showed that the HCC-LM3-exos (the exosomes secreted by HCC-LM3 cells, 50 μg mL−1) significantly promoted the proliferation and migration of HCC-LM3 cells. HCC-LM3-exos also promoted the proliferation and migration of SMMC-7721 and HL-7702 cells at 1000 and 1500 μg mL−1, respectively. With an increase in time and concentration, the proliferation effect was more significant. On comparing the mechanical properties of the three types of cells (HCC-LM3, SMMC-7721 and HL-7702 cells), the degradation degree and migration ability of the cells were from high to low in the above order. In turn, the surface roughness of the cells decreased, and adhesion and elastic modulus increased. With an increase in treatment time, surface roughness increased, while adhesion and elastic modulus decreased. These suggested that the HCC-LM3-exos could change the mechanical properties of cells, leading to their deterioration, and enhance their migration and invasion ability. In this paper, the effects of exosomes were analyzed from the perspective of the physical parameters of cells, which provide a new idea to study cancer metastasis and prognosis.

16 October 2020 in Beilstein Journal of Nanotechnology
Verified
Journal Article
Open access
PDF file
JZJingran Zhang
Jingran Zhang
TJTianqi Jia
Tianqi Jia
XLXiaoping Li
Xiaoping Li
JYJunjie Yang
Junjie Yang
ZLZhengkai Li
Zhengkai Li
ZWZuobin Wang
Zuobin Wang
Based on an electrochemical method, three-dimensional arrayed nanopore structures are machined onto a Mg surface. The structured Mg surface is coated with a thin gold (Au) film, which is used as a surface-enhanced Raman scattering (SERS) substrate. A rhodamine 6G (R6G) probe molecule is used as the detection agent for the SERS measurement. Different sizes of arrayed micro/nanostructures are fabricated by different treatment time using the electrochemical process. The topographies of these micro/nanostructures and the thickness of the Au film have an influence on the Raman intensity of the Mg substrate. Furthermore, when the thickness of Au film coating is held constant, the Raman intensity on the structured Mg substrates is about five times higher after a treatment time of 1 min when compared with other treatment times. The SERS enhancement factor ranges from 106 to 1.75 × 107 under these experimental conditions. Additionally, a 10−6 mol·L−1 solution of lysozyme was successfully detected using the Mg–Au nanopore substrates. Our low-cost method is reproducible, homogeneous, and suitable for the fabrication of SERS substrates.

2 May 2022 in Discover Nano
Verified
Journal Article
Open access
PDF file
YGYanquan Geng
Yanquan Geng
JWJiqiang Wang
Jiqiang Wang
ZLZihan Li
Zihan Li
YYYongda Yan
Yongda Yan
JZJingran Zhang
Jingran Zhang
YGYang Gan
Yang Gan
Fabrication of periodic nanostructures has drawn increasing interest owing to their applications of such functional structures in optics, biomedical and power generation devices. Nano-indentation technique has been proven as a method to fabricate periodic nanostructures. In this study, the molecular dynamic simulation approach is employed to investigate the nano-indentation process for fabricating periodic nano-pit arrays using a single indenter and an indenter array. The morphologies of indentations that machined using these two kinds of indenters are compared. The indentation force and the defect evolution during the nano-indentation process are further studied. Results show that indentation morphologies obtained by single indenter are mainly depended on the spacing of indenters, and a nano-pit array with a better shape and consistency can be obtained easier using the indenter array compared with using a single indenter. The stacking faults and dislocations induced by indentation are depended on the spacing of the indenters. Our findings are significant for understanding the differences of indentation processes using a single indenter and an indenter array and machining a high-quality periodic nano-pit array with high machining efficiency. Graphical Abstract

13 December 2019 in Beilstein Journal of Nanotechnology
Verified
Journal Article
Open access
PDF file
JZJingran Zhang
Jingran Zhang
TJTianqi Jia
Tianqi Jia
YYYongda Yan
Yongda Yan
LWLi Wang
Li Wang
PMPeng Miao
Peng Miao
ZWZuobin Wang
Zuobin Wang
Nanostructures have been widely employed in surface-enhanced Raman scattering (SERS) substrates. Recently, in order to obtain a higher enhancement factor at a lower detection limit, hierarchical structures, including nanostructures and nanoparticles, appear to be viable SERS substrate candidates. Here we describe a novel method integrating the nanoindentation process and chemical redox reaction to machine a hierarchical SERS substrate. The micro/nanostructures are first formed on a Cu(110) plane and then Ag nanoparticles are generated on the structured copper surface. The effect of the indentation process parameters and the corrosion time in the AgNO3 solution on the Raman intensities of the SERS substrate with hierarchical structures are experimentally studied. The intensity and distribution of the electric field of single and multiple Ag nanoparticles on the surface of a plane and with multiple micro/nanostructures are studied with COMSOL software. The feasibility of the hierarchical SERS substrate is verified using R6G molecules. Finally, the enhancement factor using malachite green molecules was found to reach 5.089 × 109, which demonstrates that the production method is a simple, reproducible and low-cost method for machining a highly sensitive, hierarchical SERS substrate.