Light-emitting diode (LED) combined with quantum dots (QDs) is an important candidate for next-generation high-quality semiconductor devices. However, the effect of the excitation wavelength on their optical performance has not been fully explored. In this study, green and red QDs are applied to LEDs of different excitation wavelengths from 365 to 455 nm. The blue light is recommended for exciting QDs from the perspective of energy utilization. However, QD LEDs excited at 365 nm have unique advantages in eliminating the original peaks from the LED chip. Moreover, the green or red light excited by ultraviolet light has an advantage in colorimetry. Even for the 455 nm LED with the highest QD concentration at 7.0 wt%, the color quality could not compete with the 365 nm LED with the lowest QD concentration at 0.2 wt%. A 117.5% (NTSC1953) color gamut could be obtained by the 365 nm-excited RGB system, which is 32.6% higher than by the 455 nm-excited solution, and this can help expand the color gamut of LED devices. Consequently, this study provides an understanding of the properties of QD-converted LEDs under different wavelength excitations, and offers a general guide to selecting a pumping source for QDs.

We propose a patterned leadframe substrate (PLS) configuration for light-emitting diode chip-on-board devices (LED COBs) with regular triangular structures on it. The mechanism of this method is analyzed through ray dynamics, which indicate that the light-propagating regimes are considerably different as the structure inclination angle α changes. For typical encapsulant materials (refractive index=1.41), the optimal α is 22.5^°~45^°. Then the performance of LED COB devices with PLS configurations are verified through 3-D Monte Carlo ray-tracing simulations as well as experimental measurements. Results show that the light-extraction efficiency is significantly improved. A simulated enhancement of 42% and a measured enhancement of 41.07% are observed. These results are in good consistency with the ray dynamic analysis, confirming our predictions about PLS methods. Furthermore, we find that such an LED COB configuration also provides a way to change the angular distribution of intensity from half-peak side angle 101.84^° to 141.80^°. The findings of our work represent a new concept for LED COB packaging design of great practicality in building lighting systems.

In this report, a blue anti-transmission film (BATF) has been introduced to improve the color-conversion efficiency (CCE) and the stability of quantum dot (QD) films. The results indicate that the CCE can be increased by as much as 93% using 15 layers of BATFs under the same QD concentration. Therefore, the same CCE can be achieved using BATF-QD hybrid films with a lower QD concentration when compared with standard QD films. The hybrid and QD films with the same CCE of 60% were aged at an environmental temperature of 25°C and with a 10 mA injection current light-emitting diode source. The CCE and luminous efficacy that are gained by the hybrid film increased by 42.8% and 24.5%, respectively, when compared with that gained by the QD film after aging for the same time period of approximately 65 h. In addition, the hybrid film can effectively suppress the red-shift phenomenon of the QD light spectra, as well as an expansion of the full-width at half maximum. Consequently, these BATF-QD hybrid films with excellent optical performance and stability show great potential for illumination and display applications.

Using freeform lenses to construct uniform illumination systems is important in light-emitting diode (LED) devices. In this paper, the energy feedback design is used for freeform lens (EFFL) constructions by solving a set of partial differential equations that describe the mapping relationships between the source and the illumination pattern. The simulation results show that the method can overcome the illumination deviation caused by the extended light source (ELS) problem. Furthermore, a uniformity of 95.6% is obtained for chip-on-board (COB) compact LED devices. As such, prototype LEDs manufactured with the proposed freeform lenses demonstrate significant improvements in luminous efficiency and emission uniformity.

The ability to precisely obtain tunable spectrum of lead halide perovskite quantum dots (QDs) is very important for applications, such as in lighting and display. Herein, we report a microchannel reactor method for synthesis of CsPbBr₃ QDs with tunable spectrum. By adjusting the temperature and velocity of the microchannel reactor, the emission peaks of CsPbBr₃ QDs ranging from 520 nm to 430 nm were obtained, which is wider than that of QDs obtained in a traditional flask without changing halide component. The mechanism of photoluminescence (PL) spectral shift of CsPbBr₃ QDs was investigated, the result shows that the supersaturation control enabled by the superior mass and heat transfer performance in the microchannel is the key to achieve the wide range of PL spectrum, with only a change in the setting of the temperature controller required. The wide spectrum of CsPbBr₃ QDs can be applied to light-emitting diodes (LEDs), photoelectric sensors, lasers, etc.

White light-emitting diodes (WLEDs) based on quantum dots (QDs) are gaining increasing attention due to their excellent color quality. QDs films with planar structure are universally applied in WLEDs for color conversion, while they still face great challenges in high light extraction and thermal stability. In this study, a QDs film with a spherical shell structure was proposed to improve the optical and thermal performance for WLEDs. Compared with the conventional planar structure, the luminous efficacy of the QDs spherical shell structure is improved by 12.9% due to the reduced total reflection effect, and the angular-dependent correlated color temperature deviation is decreased from 2642 to 283 K. Moreover, the highest temperature of the WLED using a QDs spherical shell is 4.8 °C lower than that of the conventional WLED with a planar structure, which is mainly attributed to larger heat dissipation area and separated heat source. Consequently, this QDs spherical shell structure demonstrates superior performance of QDs films for WLEDs applications.