Nanofluids and nanotechnology are very important in enhancing heat transfer due to the thermal conductivity of their nanoparticles, which play a vital role in heat transfer applications. Researchers have used cavities filled with nanofluids for two decades to increase the heat-transfer rate. This review also highlights a variety of theoretical and experimentally measured cavities by exploring the following parameters: the significance of cavities in nanofluids, the effects of nanoparticle concentration and nanoparticle material, the influence of the inclination angle of cavities, heater and cooler effects, and magnetic field effects in cavities. The different shapes of the cavities have several advantages in multiple applications, e.g., L-shaped cavities used in the cooling systems of nuclear and chemical reactors and electronic components. Open cavities such as ellipsoidal, triangular, trapezoidal, and hexagonal are applied in electronic equipment cooling, building heating and cooling, and automotive applications. Appropriate cavity design conserves energy and produces attractive heat-transfer rates. Circular microchannel heat exchangers perform best. Despite the high performance of circular cavities in micro heat exchangers, square cavities have more applications. The use of nanofluids has been found to improve thermal performance in all the cavities studied. According to the experimental data, nanofluid use has been proven to be a dependable solution for enhancing thermal efficiency. To improve performance, it is suggested that research focus on different shapes of nanoparticles less than 10 nm with the same design of the cavities in microchannel heat exchangers and solar collectors.

The rapid changes in nanotechnology over the last ten years have given scientists and engineers a lot of new things to study. The nanofluid constitutes one of the most significant advantages that has come out of all these improvements. Nanofluids, colloid suspensions of metallic and nonmetallic nanoparticles in common base fluids, are known for their astonishing ability to transfer heat. Previous research has focused on developing mathematical models and using varied geometries in nanofluids to boost heat transfer rates. However, an accurate mathematical model is another important factor that must be considered because it dramatically affects how heat flows. As a result, before using nanofluids for real-world heat transfer applications, a mathematical model should be used. This article provides a brief overview of the Tiwari and Das nanofluid models. Moreover, the effects of different geometries, nanoparticles, and their physical properties, such as viscosity, thermal conductivity, and heat capacity, as well as the role of cavities in entropy generation, are studied. The review also discusses the correlations used to predict nanofluids’ thermophysical properties. The main goal of this review was to look at the different shapes used in convective heat transfer in more detail. It is observed that aluminium and copper nanoparticles provide better heat transfer rates in the cavity using the Tiwari and the Das nanofluid model. When compared to the base fluid, the Al₂O₃/water nanofluid’s performance is improved by 6.09%. The inclination angle of the cavity as well as the periodic thermal boundary conditions can be used to effectively manage the parameters for heat and fluid flow inside the cavity.

Although oil extraction is indispensable for meeting worldwide energy demands and ensuring industrial sustainability, various hazards are observed. Therefore, this study examined the chemical oil recovery-related environmental consequences concerning water, soil, ecosystem, and human health damages. A numerical analysis explored the mathematical model for oil extraction from unconventional sources by utilising 3D porous prism geometries under high-temperature conditions. This unique methodology utilised environmentally friendly TiO₂-SiO₂ hybrid nanoparticles, which were not previously investigated. The optimal conditions for oil extraction were then determined by simulations performed at 100 °C, 150 °C, and 200 °C for 2 h, 4 h, 8 h, and 12 h. This study also explored the optimisation of recovery rates by analysing several variables using ANSYS Fluent software, such as flow rate, porosity, and volume fraction. Consequently, these green TiO₂-SiO₂ nanoparticles presented an oil recovery rate that was 28 % and 6 % higher than water-flooding and conventional monofluid injection techniques, respectively. This outcome suggested that these TiO₂-SiO₂ nanoparticles could enhance efficiency and minimise environmental damage.

In the field of biomedical image reconstruction, functional near infra-red spectroscopy (fNIRs) is a promising technology that uses near infra-red light for non-invasive imaging and reconstruction. Reconstructing an image requires both forward and backward problem-solving in order to figure out what the image’s optical properties are from the boundary data that has been measured. Researchers are using a variety of numerical methods to solve both the forward and backward problems in depth. This study will show the latest improvements in numerical methods for solving forward and backward problems in fNIRs. The physical interpretation of the forward problem is described, followed by the explanation of the state-of-the-art numerical methods and the description of the toolboxes. A more in-depth discussion of the numerical solution approaches for the inverse problem for fNIRs is also provided.

Enhanced oil recovery (EOR) has been offered as an alternative to declining crude oil production. EOR using nanotechnology is one of the most innovative trends in the petroleum industry. In order to determine the maximum oil recovery, the effect of a 3D rectangular prism shape is numerically investigated in this study. Using ANSYS Fluent software(2022R1), we develop a two-phase mathematical model based on 3D geometry. This research examines the following parameters: flow rate Q = 0.01–0.05 mL/min, volume fractions = 0.01–0.04%, and the effect of nanomaterials on relative permeability. The result of the model is verified with published studies. In this study, the finite volume method is used to simulate the problem, and we run simulations at different flow rates while keeping other variables constant. The findings show that the nanomaterials have an important effect on water and oil permeability, increasing oil mobility and lowering IFT, which increases the recovery process. Additionally, it has been noted that a reduction in the flow rate improves oil recovery. Maximum oil recovery was attained at a 0.05 mL/min flow rate. Based on the findings, it is also demonstrated that Si${\mathrm{O}}_2$ provides better oil recovery compared to A${\mathrm{l}}_2{\mathrm{O}}_3$. When the volume fraction concentration increases, oil recovery ultimately increases.