Nanofluids and nanotechnology are very important in enhancing heat transfer due to the thermal conductivity of their nanoparticles, which play a vital role in heat transfer applications. Researchers have used cavities filled with nanofluids for two decades to increase the heat-transfer rate. This review also highlights a variety of theoretical and experimentally measured cavities by exploring the following parameters: the significance of cavities in nanofluids, the effects of nanoparticle concentration and nanoparticle material, the influence of the inclination angle of cavities, heater and cooler effects, and magnetic field effects in cavities. The different shapes of the cavities have several advantages in multiple applications, e.g., L-shaped cavities used in the cooling systems of nuclear and chemical reactors and electronic components. Open cavities such as ellipsoidal, triangular, trapezoidal, and hexagonal are applied in electronic equipment cooling, building heating and cooling, and automotive applications. Appropriate cavity design conserves energy and produces attractive heat-transfer rates. Circular microchannel heat exchangers perform best. Despite the high performance of circular cavities in micro heat exchangers, square cavities have more applications. The use of nanofluids has been found to improve thermal performance in all the cavities studied. According to the experimental data, nanofluid use has been proven to be a dependable solution for enhancing thermal efficiency. To improve performance, it is suggested that research focus on different shapes of nanoparticles less than 10 nm with the same design of the cavities in microchannel heat exchangers and solar collectors.

The rapid changes in nanotechnology over the last ten years have given scientists and engineers a lot of new things to study. The nanofluid constitutes one of the most significant advantages that has come out of all these improvements. Nanofluids, colloid suspensions of metallic and nonmetallic nanoparticles in common base fluids, are known for their astonishing ability to transfer heat. Previous research has focused on developing mathematical models and using varied geometries in nanofluids to boost heat transfer rates. However, an accurate mathematical model is another important factor that must be considered because it dramatically affects how heat flows. As a result, before using nanofluids for real-world heat transfer applications, a mathematical model should be used. This article provides a brief overview of the Tiwari and Das nanofluid models. Moreover, the effects of different geometries, nanoparticles, and their physical properties, such as viscosity, thermal conductivity, and heat capacity, as well as the role of cavities in entropy generation, are studied. The review also discusses the correlations used to predict nanofluids’ thermophysical properties. The main goal of this review was to look at the different shapes used in convective heat transfer in more detail. It is observed that aluminium and copper nanoparticles provide better heat transfer rates in the cavity using the Tiwari and the Das nanofluid model. When compared to the base fluid, the Al₂O₃/water nanofluid’s performance is improved by 6.09%. The inclination angle of the cavity as well as the periodic thermal boundary conditions can be used to effectively manage the parameters for heat and fluid flow inside the cavity.

It is necessary to sustain energy from an external reservoir or employ advanced technologies to enhance oil recovery. A greater volume of oil may be recovered by employing nanofluid flooding. In this study, we investigated oil extraction in a two-phase incompressible fluid in a two-dimensional rectangular porous homogenous area filled with oil and having no capillary pressure. The governing equations that were derived from Darcy’s law and the mass conservation law were solved using the finite element method. Compared to earlier research, a more efficient numerical model is proposed here. The proposed model allows for the cost-effective study of heating-based inlet fluid in enhanced oil recovery (EOR) and uses the empirical correlations of the nanofluid thermophysical properties on the relative permeability equations of the nanofluid and oil, so it is more accurate than other models to determine the higher recovery factor of one nanoparticle compared to other nanoparticles. Next, the effect of nanoparticle volume fraction on flooding was evaluated. EOR via nanofluid flooding processes and the effect of the intake temperatures (300 and 350 K) were also simulated by comparing three nanoparticles: ${\mathrm{SiO}}_2$, ${\mathrm{Al}}_2{\mathrm{O}}_3$, and $\mathrm{CuO}$. The results show that adding nanoparticles (<5 v%) to a base fluid enhanced the oil recovery by more than 20%. Increasing the inlet temperature enhanced the oil recovery due to changes in viscosity and density of oil. Increasing the relative permeability of nanofluid while simultaneously reducing the relative permeability of oil due to the presence of nanoparticles was the primary reason for EOR.

Nowadays, oil companies employ nanofluid flooding to increase oil production from oil reservoirs. Herein the present work, a multiphase flow in porous media was used to simulate oil extraction from a three-dimensional porous medium filled with oil. Interestingly, the finite element method was used to solve the nonlinear partial differential equations of continuity, energy, Darcy’s law, and the transport of nanoparticles (NPs). The proposed model used nanofluids (NFs) empirical formulas for density and viscosity on NF and oil relative permeabilities and NP transport equations. The NPs thermophysical properties have been investigated and compared with their oil recovery factor (ORF) to determine the highest ORF. Different NPs (SiO${}_2$, CuO, and Al${}_2$O${}_3$) were used as the first parameter, keeping all parameters constant. The simulation was run three times for the injected fluid using the various NPs to compare the effects on enhanced oil recovery. The second parameter, volume fraction (VF), has been modeled six times (0.5, 1, 2, 3, 4, and 5%), with all other parameters held constant. The third parameter, the injected NF inlet temperature (293.15–403.15 K), was simulated assuming that all other parameters are kept constant. The energy equation was applied to choose the inlet temperature that fits the optimum NP and VF to determine the highest ORF. Findings indicated that SiO${}_2$ shows the best ORF compared to the other NPs. Remarkably, SiO${}_2$ has the lowest density and highest thermal capacity. The optimum VF of SiO${}_2$ was 4%, increasing the ORF but reduced when the VF was higher than 4%. The ORF was improved when the viscosity and density of the oil decreased by increasing the injected inlet temperature. Furthermore, the results indicated that the highest ORF of 37% was obtained at 353.15 K when SiO${}_2$ was used at a VF of 4%. At the same time, the lowest recovery is obtained when a volume of 5% was used at 403.15 K.

Two-phase Darcy’s law is a well-known mathematical model used in the petrochemical industry. It predicts the fluid flow in reservoirs and can be used to optimize oil production using recent technology. Indeed, various models have been proposed for predicting oil recovery using injected nanofluids (NFs). Among them, numerical modeling is attracting the attention of scientists and engineers owing to its ability to modify the thermophysical properties of NFs such as density, viscosity, and thermal conductivity. Herein, a new model for simulating NF injection into a 3D porous media for enhanced oil recovery (EOR) is investigated. This model has been developed for its ability to predict oil recovery across a wide range of temperatures and volume fractions (VFs). For the first time, the model can examine the changes and effects of thermophysical properties on the EOR process based on empirical correlations depending on two variables, VF and inlet temperature. The governing equations obtained from Darcy’s law, mass conservation, concentration, and energy equations were numerically evaluated using a time-dependent finite-element method. The findings indicated that optimizing the temperature and VF could significantly improve the thermophysical properties of the EOR process. We observed that increasing the inlet temperature (353.15 K) and volume fraction (4%) resulted in better oil displacement, improved sweep efficiency, and enhanced mobility of the NF. The oil recovery decreased when the VF (>4%) and temperature exceeded 353.15 K. Remarkably, the optimal VF and inlet temperature for changing the thermophysical properties increased the oil production by 30%.

The use of nanomaterials as a means of recovering heavy and light oil from petroleum reservoirs has increased over the preceding twenty years. Most researchers have found that injecting a nanoparticle dispersion (nanofluids) has led to good results and increased the amount of oil that can be recovered. In this research, we aim to imitate the three-dimensional hexagonal prism in the existence of SiO2 and Al2O3 nanoparticles for better oil recovery. Porosity ($0.1\le \phi \le 0.4$), mass flow rate ($0.05mL/\mathit{min}\le Q\le 0.05ml/\mathit{min}$), nanoparticle concentration ($0.01\le \psi \le 0.04$), and the effect of relative permeability (kr) on oil and water saturation in the presence of gravity under different time durations are all investigated. The result obtained for the model is verified with existing experimental data. The results indicated that the infulence of nanoparticle volume fraction (VF) is significant in enhancing the oil recovery rate. It is also observed that at low porosity values the oil recovery is maximum. The maximum oil recovery is attained at low values of mass flow rate in the 3D hexagonal prism in the presence of silicon and aluminium nanoparticles It is also observed that the use of SiO2 gives a better oil recovery rate than Al2O3. It is also observed that maximum oil recovery is obtained at 99% at a flow rate of 0.05 mL/min in the presence of silicon injection.