Indoor localization of a mobile target represents a prominent application within wireless sensor network (WSN), showcasing significant values and scientific interest. Interference, obstacles, and energy consumption are critical challenges for indoor applications and battery replacements. A proposed tracking system deals with several factors such as latency, energy consumption, and accuracy presenting an innovative solution for the mobile localization application. In this paper, a novel algorithm introduces a self-localization algorithm for mobile targets using the wake-up media access control (MAC) protocol. The developed tracking application is based on the trilateration technique with received signal strength indication (RSSI) measurements. Simulations are implemented in the objective modular network testbed in C++ (OMNeT++) discrete event simulator using the C++ programming language, and the RSSI values introduced are based on real indoor measurements. In addition, a determination approach for finding the optimal parameters of RSSI is assigned to implement for the simulation parameters. Simulation results show a significant reduction in power consumption and exceptional accuracy, with an average error of 1.91 m in 90% of cases. This method allows the optimization of overall energy consumption, which consumes only 2.69% during the localization of 100 different positions.

With the introduction of Internet of Things (IoT) technology in several sectors, wireless, reliable, and energy-saving communication in distributed sensor networks are more important than ever. Thereby, wake-up technologies are becoming increasingly important as they significantly contribute to reducing the energy consumption of wireless sensor nodes. In an indoor environment, the use of wireless sensors, in general, is more challenging due to signal fading and reflections and needs, therefore, to be critically investigated. This paper discusses the performance analysis of wake-up receiver (WuRx) architectures based on two low frequency (LF) amplifier approaches with regard to sensitivity, power consumption, and package error rate (PER). Factors that affect systems were compared and analyzed by analytical modeling, simulation results, and experimental studies with both architectures. The developed WuRx operates in the 868 MHz band using on-off-keying (OOK) signals while supporting address detection to wake up only the targeted network node. By using an indoor setup, the signal strength and PER of received signal strength indicator (RSSI) in different rooms and distances were determined to build a wireless sensor network. The results show a wake-up packets (WuPts) detection probability of about 90% for an interior distance of up to 34 m.

Wake-up receivers are gaining importance in power-aware wireless sensor networks, as they significantly reduce power consumption during RF reception, enabling asynchronous communication with low latency. However, the performance of wake-up receivers still lags behind that of off-the-shelf RF transceivers. There is a growing demand for higher sensitivity, enhanced reliability, and lower latency while maintaining the lowest power consumption. In this article, our goal is to advance the performance of wake-up receivers based on off-the-shelf components and low-frequency pattern matchers. Through a systematic investigation, we proposed multiple improvements aimed at enhancing wake-up receiver performance and reliability. We introduced an improved passive envelope detector and realized a wake-up receiver for the 868 MHz band, which achieves a power consumption of $5.71$ μW and latency of $9.02$ ms. Our proposed wake-up receiver is capable of detecting signals down to an average power level of $-61.6$ dBm. These achievements represent significant advancements compared to the existing state of research on wake-up receivers based on low-frequency pattern matchers. Recent articles have not been able to attain such improved values in signal detection, power consumption, and latency.

The Wireless Sensor Network (WSN) is one of the most promising solutions for the supervision of multiple phenomena and for the digitisation of the Internet of Things (IoT). The Wake-up Receiver (WuRx) is one of the most trivial and effective solutions for energy-constrained networks. This technology allows energy-autonomous on-demand communication for continuous monitoring instead of the conventional radio. The routing process is one of the most energy and time-consuming processes in WSNs. It is, hence, crucial to conceive an energy-efficient routing process. In this paper, we propose a novel Wake-up Receiver-based routing protocol called Clustered WuRx based on Multicast wake-up (CWM), which ensures energy optimisation and time-efficiency at the same time for indoor scenarios. In our proposed approach, the network is divided into clusters. Each Fog Node maintains the routes from each node in its cluster to it. When a sink requires information from a given node, it’s corresponding Fog Node uses a multicast wake-up mechanism to wake up the intended node and all the intermediate nodes that will be used in the routing process simultaneously. Measurement results demonstrate that our proposed approach exhibits higher energy efficiency and has drastic performance improvements in the delivery delay compared with other routing protocols.

For power-limited wireless sensor networks, energy efficiency is a critical concern. Receiving packets is proven to be one of the most power-consuming tasks of a wireless sensor node. Wake-up receivers enable asynchronous communication while maintaining low power consumption. Recent wake-up receiver designs have low sensitivity, high power consumption, or lack of reliability and reproducibility. The proposed receiver circuit utilizes a two-stage low-noise amplifier to achieve a sensitivity of -80 dBm. A duty-cycling approach was introduced to reduce the average power consumption to 14.2 $\mu \mathrm{W}$ . The reliability of the proposed design was ensured by introducing a special low-frequency modulation scheme. The reproducibility of the design was ensured by only using commercial off-the-shelf components.