Zhenzhuo Zhang

Mr. Zhenzhuo Zhang

Institute of Semiconductors, Beijing, China
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 February 2023 in Optics Express
Verified
Journal Article
Closed access
ZZZhenzhuo Zhang
Zhenzhuo Zhang
JYJing Yang
Jing Yang
FLFeng Liang
Feng Liang
PCPing Chen
Ping Chen
ZLZongshun Liu
Zongshun Liu
DZDegang Zhao
Degang Zhao
Performance of InGaN-based blue-violet laser diodes (LD) with different waveguide structure were investigated by simulation and experimental methods. Theoretical calculation demonstrated that threshold current (Ith) can be reduced and slope efficiency (SE) can be improved by using an asymmetric waveguide structure. Based on the simulation results, a LD with 80-nm-thick In0.03Ga0.97N lower waveguide (LWG) and 80-nm-thick GaN upper waveguide (UWG) is fabricated with flip chip package. Under continuous wave (CW) current injection at room temperature, its optical output power (OOP) reaches 4.5 W at an operating current of 3 A and the lasing wavelength of 403 nm. The threshold current density (Jth) is 0.97 kA/cm2 and the SE is about 1.9 W/A.

1 September 2022 in AIP Advances
Verified
Journal Article
Open access
PDF file
ZZZhenzhuo Zhang
Zhenzhuo Zhang
JYJing Yang
Jing Yang
Degang ZhaoDegang Zhao
Degang Zhao
BWBaibin Wang
Baibin Wang
YZYuheng Zhang
Yuheng Zhang
YBYuhao Ben
Yuhao Ben
The reaction between gallium (Ga) and silicon (Si), termed melt-back etching, greatly deteriorates the quality of GaN grown on a Si substrate. In this paper, the mechanism of melt-back etching was investigated layer-by-layer in a GaN/AlN/Si system. It is found that the environment of the reactor plays a critical role in melt-back etching, which may happen as early as during the baking process. Drawing on experimental evidence and analyses, a two-step melt-back etching model is proposed. Finally, optimized pretreatments including an AlN precoating process and reduction in baking temperature were used to successfully solve the etching problem and verify the model.

12 November 2022 in Nanomaterials
Verified
Journal Article
Open access
PDF file
ZZZhenzhuo Zhang
Zhenzhuo Zhang
JYJing Yang
Jing Yang
Degang ZhaoDegang Zhao
Degang Zhao
FLFeng Liang
Feng Liang
PCPing Chen
Ping Chen
ZLZongshun Liu
Zongshun Liu
Electron leakage has an adverse influence on the optical output power for laser diodes (LDs), especially where the conventional last quantum barrier (LQB) in the multiple quantum well (MQW) active region may cause severe leakage problems. In this article, a composite last quantum barrier (CLQB) composed of p-type doped AlGaN (p-AlGaN) and unintentionally doped GaN (u-GaN) layers is designed to replace the conventional one, for overcoming the problem of electron overflow. Theoretical calculations with LASTIP software demonstrate that CLQB with optimized parameters of Al composition, thickness and p-type doping concentration of the p-AlGaN layer in the CLQB can have a 50% improvement in slope efficiency (SE) compared with the conventional structure LD. This will help to realize a higher optical output power in InGaN-based violet LDs.

7 November 2023 in Optics Express
Verified
Journal Article
Closed access
YHYufei Hou
Yufei Hou
BWBaibin Wang
Baibin Wang
JYJing Yang
Jing Yang
YZYuheng Zhang
Yuheng Zhang
ZZZhenzhuo Zhang
Zhenzhuo Zhang
DZDegang Zhao
Degang Zhao
The influence of growth interruption on the surface and luminescence properties of AlGaN/GaN ultraviolet multi-quantum wells (UV MQWs) is investigated. It is found that when the well and barrier layers of MQW samples are continuously grown at the same temperature, they have lower edge dislocation density and flatter surface of MQWs compared to samples with interrupted well and barrier growth. Moreover, continuous growth of well and barrier layers is more conducive to improving the luminescence efficiency of MQWs. This phenomenon is attributed to more impurity incorporation induced by the growth interruption, while a continuous growth of well and barrier can reduce surface diffusion and migration processes of atoms, reducing the defects and surface roughness of MQWs. In addition, the continuous growth of well and barrier can better control the reaction between Al and N atoms, avoiding the formation of excessively high Al content AlGaN at the well/barrier interface, thus improving the luminescence of UV MQWs.

12 August 2022 in Crystals
Verified
Journal Article
Open access
PDF file
BWBaibin Wang
Baibin Wang
JYJing Yang
Jing Yang
Degang ZhaoDegang Zhao
Degang Zhao
YZYuheng Zhang
Yuheng Zhang
ZZZhenzhuo Zhang
Zhenzhuo Zhang
ZLZongshun Liu
Zongshun Liu
The mechanisms of AlGaN device buffer layer growth were studied. Gallium residues in the reactor chamber may be harmful to the quality of the AlN strain modulation layer, which eventually worsens the AlGaN buffer layer. By restraining the gallium residues, the crystalline quality of the AlGaN layer is markedly improved. In addition, enhancing stress relief in nucleation and coalescence stages will reduce the edge dislocations induced by strain relaxation in the 2D growth stage. A slower precursor flow rate can promote the stress relief in nucleation and coalescence stages. By comparison, a suitable suppression of Al atoms’ surface migration can decrease surface roughness, which can be realized by increasing the precursor flow rate. Eventually, we obtained a AlGaN buffer layer having both low edge dislocation density and a flat surface using a two-step growth method.

11 March 2023 in Journal of Crystal Growth
Verified
Journal Article
Closed access
ZZZhenzhuo Zhang
Zhenzhuo Zhang
JYJing Yang
Jing Yang
YHYujie Huang
Yujie Huang
FLFeng Liang
Feng Liang
PCPing Chen
Ping Chen
DZDegang Zhao
Degang Zhao