Paweł Just

Dr. Paweł Just

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 July 2022 in Combustion Engines
Verified
Journal Article
Open access
MWMarek Wozniak
Marek Wozniak
KSKrzysztof Siczek
Krzysztof Siczek
SZSergiusz Zakrzewski
Sergiusz Zakrzewski
PJPaweł Just
Paweł Just
GOGustavo Ozuna
Gustavo Ozuna
COConstantin Onescu
Constantin Onescu
The exhaust gas recirculation (EGR) valve regulates the exhaust gas flow between the engine exhaust manifold and the inlet one. This allows the inlet air to warm up, improving fuel evaporation and reducing the combustion temperature of the charge. Such a valve reduces the number of harmful substances in the exhaust gas. The valve sticks when too much sediment builds on the walls of the exhaust system, especially during driving in urban conditions or when leaks in the vacuum or exhaust pipes occur. A faulty valve causes the engine to run unevenly at idle speed and under light loads. The defective EGR valve weakens the inlet manifold capacity, increases combustion, clogging of the particulate filter, damage to the lambda probe. A blocked EGR valve may lead to engine immobilization as a result of the operation of its computerized control system. A model of the EGR valve of a selected diesel engine was developed to determine the velocity distribution of the load flowing in it for different values of the degree of valve opening and the volume of deposits on the valve walls. The volume of accumulated carbon deposits on the walls of the EGR valve was measured using a real engine. Based on the recorded mileage of the vehicle, the assumed average speed of the car, and the driving style of the driver, the intensity of deposition of carbon particles on the walls was estimated.

23 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
Grzegorz GumiennyGrzegorz Gumienny
Grzegorz Gumienny
Boguslaw PisarekBoguslaw Pisarek
Boguslaw Pisarek
Tomasz SzymczakTomasz Szymczak
Tomasz Szymczak
JGJakub Gawroński
Jakub Gawroński
PJPaweł Just
Paweł Just
TPTadeusz Pacyniak
Tadeusz Pacyniak
The article is devoted to the optimization of the degassing parameters of the AlSi9Cu3(Fe) alloy. The alloy was degassed with a solid degasser (Ecosal) and nitrogen or argon. The variable parameters were time and type of degasser. The test castings were made in permanent molds with an internal diameter of 25 mm and a length of 150 mm. The effect of the degassing time and the amount of degasser on the mechanical properties, as well as the hydrogen content and density index were investigated. The ALU SPEED TESTER developed by FMA was used to test the hydrogen content and the density index. Magmasoft software was used to design the geometry of the test castings. A significant effect of the solid degasser and degassing time on both the density index and the hydrogen content was demonstrated. Replacing nitrogen with argon did not bring any significant improvement in the above-mentioned parameters. The effect of degassing parameters on the mechanical properties of the EN AC-46000 alloy was much less significant, but was still visible. The optimal degassing parameters needed to obtain the highest strength parameters of the EN AC-46000 gravity die castings were determined.

17 February 2025 in Materials
Verified
Journal Article
Open access
PDF file
Tomasz SzymczakTomasz Szymczak
Tomasz Szymczak
Boguslaw PisarekBoguslaw Pisarek
Boguslaw Pisarek
Cezary RapiejkoCezary Rapiejko
Cezary Rapiejko
RWRyszard Władysiak
Ryszard Władysiak
PJPaweł Just
Paweł Just
TPTadeusz Pacyniak
Tadeusz Pacyniak
This article presents studies on the effect of Sr and TiB on the crystallization process, mechanical properties, hardness, and density index of the Al-Si alloy from the EN AC-46000 group, with a narrowed chemical composition, produced by die-casting and HPDC (high-pressure die casting) technology. The research used the Box–Wilson method to design the experiment and stepwise multiple regression. To identify the optimal amount of Sr and Ti in the analyzed alloy that would simultaneously guarantee the maximization of UTS, YS, Agt, and HBW and the minimization of the DI (density index), multi-criteria optimization was performed. The modifiers were added to the liquid alloy as AlSr10 and AlTi5B1 master alloys. It was found that for 0.02–0.04 wt.% Sr and 0.05–0.08 wt.% Ti in the die castings, the highest mechanical properties, such as UTS, YS, Agt, and HBW (treated as stimulants in the experiment), can be obtained simultaneously with the lowest alloy gasification identified by DI (treated as a destimulant in the experiment). It was also confirmed that the same amount of the above-mentioned elements in HPDC castings caused an increase in UTS by approx. 14%, YS by approx. 6%, A by approx. 47%, and HBW by approx. 13%, with a relatively small increase in DI by approx. 5% compared to the unmodified alloy.

1 March 2013 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
RKR. Kaczorowski
R. Kaczorowski
PJPaweł Just
Paweł Just
TPT. Pacyniak
T. Pacyniak
The current work presents and describes the test bench for analyzing the lost foam process, especially measuring of the pressure of gases in the gas gap and continuous measuring of the rate of rise of the bath level when pouring the liquid metal into the mould. A series of preliminary research was carried out on the bench which was aimed at determining the influence of the basic parameters of the process, i.e. the density of the styrofoam pattern, thickness of the refractory coating applied on the pattern, kind of the alloy and the temperature of pouring on the mould cavity by the liquid metal and the pressure of gases in the gas gap.

12 February 2021 in Archives of Foundry Engineering
Verified
Journal Article
Closed access
Cezary RapiejkoCezary Rapiejko
Cezary Rapiejko
DMD. Mikusek
D. Mikusek
PJPaweł Just
Paweł Just
TPT. Pacyniak
T. Pacyniak
The paper presents the results of research related to the possibility of inoculation of the AZ91 magnesium alloy casted into ceramic moulds by gadolinium. Effects of gadolinium content (0.1–0.6 wt%) on microstructure of the AZ91 alloy under as-cast state were investigated. The influence of the inoculator on the formation of the microstructure investigated by means of the thermal and derivative analysis by analysing the thermal effects arising during the alloy crystallization resulting from the phases formed. The degree of fragmentation of the microstructure of the tested alloys was assessed by means of the light microscopy studies and an image analysis with statistical analysis was performed. Conducted analyses have aimed at examining on the effect of inoculation of the gadolinium on the differences between the grain diameters and average size of each type of grain by way of measuring their perimeters of all phases, preliminary αMg and eutectics αMg+γ(Mg17Al12) in the prepared examined material.

12 December 2019 in Archives of Metallurgy and Materials
Verified
Journal Article
Closed access
PDF file
Grzegorz GumiennyGrzegorz Gumienny
Grzegorz Gumienny
BKB. Kurowska
B. Kurowska
PJPaweł Just
Paweł Just
The paper presents the effect of manganese on the crystallization process, microstructure and selected properties: cast iron hardness as well as ferrite and pearlite microhardness. The compacted graphite was obtained by Inmold technology. The lack of significant effect on the temperature of the eutectic transformation was demonstrated. On the other hand, a significant reduction in the eutectoid transformation temperature with increasing manganese concentration has been shown. The effect of manganese on microstructure of cast iron with compacted graphite considering casting wall thickness was investigated and described. The nomograms describing the microstructure of compacted graphite iron versus manganese concentration were developed. The effect of manganese on the hardness of cast iron and microhardness of ferrite and pearlite were given.