José Miguel Casaca Faria Silva

Mr. José Miguel Casaca Faria Silva

INEGI
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 February 2023 in Metals
Verified
Journal Article
Open access
PDF file
Gonçalo SoaresGonçalo Soares
Gonçalo Soares
RNRui Neto
Rui Neto
Rui MadureiraRui Madureira
Rui Madureira
RSRui Soares
Rui Soares
José Miguel Casaca Faria SilvaJosé Miguel Casaca Faria Silva
José Miguel Casaca Faria Silva
LALuís Araújo
Luís Araújo
AlSi12(Fe), AlSi10Mg(Fe), AlSi10MnMg, and AlMg4Fe2 die-casting alloys were produced by high-pressure die casting (HPDC) and vacuum-assisted high-pressure die casting (VADC) under a vacuum level of 200 mbar. The chemical composition, hardness, gas and shrinkage porosity, and mechanical properties were analyzed. The parts under study were subjected to a T6 heat treatment. The VADC led to a decrease in the percentage of defects in the as-cast state for all the alloys, due to a reduction in the amount of gas porosities. After heat treatment, the quantity of gas and shrinkage porosities increased. The efficiency and level of vacuum used were not sufficient to improve the mechanical properties in the as-cast state. The ductility of AlSi10Mg(Fe) and AlSi10MnMg alloys was improved after heat treatment; however, the YS and UTS of AlSi10Mg(Fe) did not increase. The primary aluminum alloys presented higher elongation values than the secondary aluminum alloys due to the reduced amount of the needle-like β-Al5FeSi phase.

10 March 2022 in Materials
Verified
Journal Article
Open access
PDF file
Rui Pedro SilvaRui Pedro Silva
Rui Pedro Silva
RSRui Soares
Rui Soares
RNRui Neto
Rui Neto
Ana Rosanete ReisAna Rosanete Reis
Ana Rosanete Reis
RPRicardo Paiva
Ricardo Paiva
José Miguel Casaca Faria SilvaJosé Miguel Casaca Faria Silva
José Miguel Casaca Faria Silva
The effect of the application of a rotating magnetic field on the average grain size of IN718 castings was experimentally studied. For the purpose, four parts were produced by investment casting and characterized. The first casting was produced without application of RMF for comparison. The remaining ones were submitted to different RMF frequencies for 15 min and subsequently to the pouring of the nickel-based superalloy. In these three castings, the RMF frequencies applied were, respectively, 15 Hz, 75 Hz and 150 Hz. All the other process parameters were kept constant during the execution of the experimental procedure. The average grain size of the samples was determined according to the ASTM E112-13 standard, using intercept methods. Macro hardness measurements, tensile testing and SEM-EDS analysis were conducted in order to evaluate the casting’s mechanical properties and microstructures. The results demonstrate a noticeable grain size reduction in the samples submitted to rotating magnetic field. An average grain area reduction, greater than 96%, was achieved in the castings where RMF frequencies of 75 Hz and 150 Hz were applied. The application of RMF also caused a morphological change in the casting’s dendrites from cellular to almost equiaxed. Additionally, it originated the decrease of the size and amount of needle-like δ phase. Regarding mechanical properties of the cast parts, no major differences were verified.

16 September 2024 in Metals
Verified
Journal Article
Open access
PDF file
RGRui Gomes
Rui Gomes
Gonçalo SoaresGonçalo Soares
Gonçalo Soares
Rui MadureiraRui Madureira
Rui Madureira
Rui Pedro SilvaRui Pedro Silva
Rui Pedro Silva
José Miguel Casaca Faria SilvaJosé Miguel Casaca Faria Silva
José Miguel Casaca Faria Silva
Cristina M. FernandesCristina M. Fernandes
Cristina M. Fernandes
In this work, we intended to study the effect of heat treatments (T5 and flash T6) on blistering, mechanical properties and microstructure for different parts produced by vacuum-assisted HPDC. These parts were produced with primary and secondary aluminium alloys (AlSi10MnMg alloy and AlSi10Mg(Fe) alloy, respectively). The parts presented blisters for all combinations of temperature (between 360 °C and 520 °C) and stage times (15 and 30 min) of solution heat treatments. However, when subjected to the T5 heat treatment, blisters were no longer visible. With this heat treatment, there was an increase in yield strength of 64% for both aluminium alloys and an increase in UTS of 31% in AlSi10Mg(Fe) alloy and of 24% in AlSi10MnMg alloy, when compared to the mechanical properties in the as-cast state. However, there was a decrease in ductility. The AlSi10Mg(Fe) alloy presented a lot of contaminations (especially iron), which impaired the mechanical properties compared to the primary aluminium alloy, AlSi10MnMg.

10 June 2024 in Materials
Verified
Journal Article
Open access
PDF file
Filipe MonteiroFilipe Monteiro
Filipe Monteiro
Gonçalo SoaresGonçalo Soares
Gonçalo Soares
Rui MadureiraRui Madureira
Rui Madureira
Rui Pedro SilvaRui Pedro Silva
Rui Pedro Silva
José Miguel Casaca Faria SilvaJosé Miguel Casaca Faria Silva
José Miguel Casaca Faria Silva
AEAntónio José Esteves
António José Esteves
The low-pressure die casting (LPDC) process was experimentally and numerically studied to produce AlSi7Mg0.3 components such as steering knuckles. Steering knuckles are important safety components in the context of a vehicle’s suspension system, serving as the mechanical interface that facilitates the articulation of the steering to control the front wheel’s orientation, while simultaneously bearing the vertical load imposed by the vehicle’s weight. This work focuses on the development of a numerical model in ProCAST®, replicating the production of the aforementioned part. The model analyses parameters such as the filling dynamics, solidification process, and presence of shrinkage porosities. For the purpose of evaluating the quality of the castings, six parts were produced and characterised, both mechanically (tensile and hardness tests) and microstructurally (porosity and optical microscopy analysis). When correlating simulation results with the available experimental data, it is possible to conclude that the usage of the LPDC process is a viable alternative to the use of steels and other metals for the production of very high-quality castings while using lighter alloys such as aluminium and magnesium in more demanding applications.

17 February 2022 in Metals
Verified
Journal Article
Open access
PDF file
Raimundo Nonato Alves da SilvaRaimundo Nonato Alves da Silva
Raimundo Nonato Alves da Silva
Rui MadureiraRui Madureira
Rui Madureira
José Miguel Casaca Faria SilvaJosé Miguel Casaca Faria Silva
José Miguel Casaca Faria Silva
RSRui Soares
Rui Soares
Ana Rosanete ReisAna Rosanete Reis
Ana Rosanete Reis
Rui Pedro SilvaRui Pedro Silva
Rui Pedro Silva
The development of biomaterials, particularly metallic ones, is one of the focuses of the scientific community, mainly due to an increase of average life expectancy and an improvement of the casted materials combined with better mechanical properties and defect-free products. The use of cobalt alloys in applications, such as knee, hip, and dental prostheses, is the result of their good ability to maintain mechanical properties and biocompatibility over long periods of use. Numerical methods are becoming more important, as they help product improvement in a faster and economic way. This work focuses on the development of a numerical model in ProCAST®, comparing the shrinkage porosity and cooling curves with real castings. When correlating simulation results with available experimental data, it is possible to understand that the formulated model demonstrates an acceptable solution in terms of precision (shrinkage porosity and cooling curve). The alloy’s thermal properties and heat conditions were iteratively changed until the developed numerical model turned out a viable tool for this specific alloy when used in the investment casting process.