Automated fiber placement (AFP) in situ consolidation of continuous CF/high-performance thermoplastic composite is the key technology for efficient and low-cost manufacturing of large thermoplastic composites. However, the void in the in situ composite is difficult to eliminate because of the high pressure and the short consolidation time; the void content percentage consequently is the important defect that determines the performance of the thermoplastic composite parts. In this paper, based on the two-dimensional Newtonian fluid extrusion flow model, the void dynamics model and boundary conditions were established. The changes of the void content percentage were predicted by the cyclic iteration method. It was found that the void content percentage increased gradually along the direction of the layers’ thickness. With the increasing of the laying speed, the void content percentage increased gradually. With the increasing of the pressure of the roller, the void content percentage gradually decreased. When the AFP speed was 11 m/min and the pressure of the compaction roller reached 2000 N, the void content percentage of the layers fell below 2%. It was verified by the AFP test that the measured results of the layers’ thickness were in good agreement with the predicted results of the model, and the test results of the void content percentage were basically equivalent to the predicted results at different AFP speeds, which indicates that the kinetic model established in this paper is representative to predict the void content percentage. According to the metallographic observation, it was also found that the repeated pressure of the roller was helpful to reduce the void content percentage.
11 November 2021 in Journal of Composite Materials
In situ consolidation of thermoplastic composites can be realized through laser-assisted automated fiber placement (AFP) technology, and the properties of composites were significant affected by the process parameters. In this work, the effects of process parameters on the properties of continuous carbon fiber–reinforced polyphenylene sulfide (CF/PPS) composites manufactured by laser-assisted AFP were investigated. Four-plies CF/PPS prepreg was laid under the combination of different process parameters and the morphology, void content, crystallinity, and inter-laminar shear strength (ILSS) of the composites were characterized. It turned out that the resin distribution on the surface of the composites could be significantly improved by increasing the laser temperature and compaction pressure. The highest crystallinity of the composites reached 46% at tool temperature of 120°C while the value was only 18% when the tool temperature was 40°C. Meanwhile, with the increasing compaction force ranging of 500–2000 N, the void content of the composites decreased obviously. The ILSS was evaluated through double notch tensile shear test. The results indicated that the mechanical properties of the composites were dominated by void content rather than crystallinity.
In situ consolidation of the thermoplastic composites can be realized through laser-assisted automated fiber placement technology, and the properties of the composites are significantly affected by the crystallinity. Understanding the complicated crystallization process is very important for controlling the performance of the composites manufactured by automated fiber placement. In this work, the crystallization mechanism of carbon fiber/polyphenylene sulfide composites during the automated fiber placement process and its effect on the mechanical properties were investigated. Crystallization kinetics analysis indicated that the crystallization window of the carbon fiber/polyphenylene sulfide composites was 87–270°C. Furthermore, for carbon fiber/polyphenylene sulfide composites manufactured by automated fiber placement, the crystallinity was influenced by the parameters including laser temperature, placement speed and tool temperature, in which the tool temperature was the main factor. Increasing the tool temperature was an effective method to achieve high crystallinity. Meanwhile, when the tool temperature was in the range of the crystallization window, the composites could experience isothermal crystallization, which could further improve the crystallinity. With the increase of the tool temperature, the flexural strength and interlaminar shear strength were improved due to the enhanced self-adhesion of the matrix, while the Mode І fracture toughness was decreased because of the reduction of the matrix ductility. The combination of the kinetic method and experimental study was conducive to a better understanding of the crystallization mechanism and optimization of the processing conditions.
14 February 2022 in Journal of Thermoplastic Composite Materials
Carbon fiber (CF) reinforced thermoplastic composites have great potential in the aerospace industry. However, defects and delamination restrict the application of the composites. This study investigated the effect of cooling rate on the crystallization and inter-laminar fracture toughness of CF reinforced polyphenylene sulfide (CF/PPS) composites. Differential scanning calorimetry (DSC) results showed that the crystallinity of the composites decreased from 49.6% to 27.1% when the cooling rate increased from 2°C/min to 1000°C/min. Meanwhile, mode I and mode II fracture toughness, as measured by the double cantilever beam (DCB) and end-notched flexure (ENF) tests, increased by 486% and 52%, respectively. The fracture morphology of the composites after DCB tests showed that when the cooling rate was 2, 30, and 300°C/min, the crack propagation occurred inside the resin, which was a typical cohesive failure. Moreover, when the cooling rate was 1000°C/min, the crack propagation belonged to the combination of cohesive and adhesive failure, indicating that a high cooling rate was conducive to improving the fracture toughness. It also turned out that the contribution of the matrix deformation dominated the fracture toughness.
In in situ consolidation of thermoplastic composites by laser-assisted automated fibre placement (AFP), high laser irradiation temperature can improve the fluidity of the resin matrix, which usually enhances the performances of composites. However, it leads to a tendency for thermal degradation as the resin matrix of the composites is exposed to high temperatures for a long time. The thermal degradation behaviours of continuous carbon fibre (CF)-reinforced polyphenylene sulfide (PPS) composites during in situ consolidation by laser-assisted AFP were studied. A thermogravimetric analysis shows that the thermal degradation of CF/PPS composites is quite complex, with multi-step reactions. The thermal degradation of the composites was further analysed via kinetic methods. A thermal degradation kinetic model of the resin matrix was obtained and verified. According to the kinetic model, the thermal degradation of the composites under different placement conditions was predicted. The results were confirmed by Fourier-transform infrared spectroscopy and scanning electron microscopy. With the combination of the kinetic model, AFP in situ consolidation, and characterisation techniques, processing parameters such as laser irradiation temperature and placement speed can be adjusted and optimised.
Automated fiber placement (AFP) in situ consolidation (ISC) of thermoplastic composite possess the potential to reduce manufacturing costs and improve manufacturing efficiency. The properties of composite manufactured by the ISC are affected by several mechanisms including polymer degradation, crystallization, intimate contact, polymer healing and void dynamics. All these mechanisms are directly affected by the temperature history. Consequently, the control and accurate measurement of temperature history during ISC are particularly important for improving the properties of composite. In this study, a simplified three-dimensional transient heat transfer model was established. The effect of tool temperature and placement speed on the temperature history and peak temperature were predicted. Simultaneously, an online temperature monitoring system was built and the optical Fiber Bragg Grating sensors (FBGS) was used to measure the temperature history. The results indicated that the predicted results of the model were consistent with the measured results, the error was below 8%. In addition, the temperature history of layers was significantly affected by the tool temperature and placement speed. The temperature of the layers decreased to near the tool temperature after cooling, and a higher tool temperature increasing its peak temperature because of the reduce of the cooling rate. On the contrary, an increase in placement speed will reduce the peak temperature of the layers.