In order to satisfy the drastic temperature change and high chemical activity in directional solidification of Nb–Si based alloys, Y2O3 crucible is demanded to possess high thermal shock resistance and erosion resistance. This paper improved the sintering degree and density of Y2O3 crucible by optimizing the sintering temperature and time, and its practical application performance was investigated. Y2O3 grains gathered with the increase of sintering temperature and time, and the contact area enlarged, resulting in the open pores being changed into closed pores. The higher density caused the improvement of erosion resistance of Y2O3 crucibles. However, excessive density weakened the thermal shock resistance. Considering high-temperature strength, erosion resistance, thermal shock resistance and costs, optimum sintering temperature and time of Y2O3 directional solidification crucible were 1800°C and 120min, respectively, and the porosity was 20%. Improved Y2O3 crucible has been successfully applied to directional solidification of Nb–Si based alloys, and significantly reduced the oxygen contamination. Slight interaction occurred between Hf and Y2O3, but no obvious dissolution, penetration or erosion was found, showing good erosion resistance and thermal shock resistance
In situ consolidation of the thermoplastic composites can be realized through laser-assisted automated fiber placement technology, and the properties of the composites are significantly affected by the crystallinity. Understanding the complicated crystallization process is very important for controlling the performance of the composites manufactured by automated fiber placement. In this work, the crystallization mechanism of carbon fiber/polyphenylene sulfide composites during the automated fiber placement process and its effect on the mechanical properties were investigated. Crystallization kinetics analysis indicated that the crystallization window of the carbon fiber/polyphenylene sulfide composites was 87–270°C. Furthermore, for carbon fiber/polyphenylene sulfide composites manufactured by automated fiber placement, the crystallinity was influenced by the parameters including laser temperature, placement speed and tool temperature, in which the tool temperature was the main factor. Increasing the tool temperature was an effective method to achieve high crystallinity. Meanwhile, when the tool temperature was in the range of the crystallization window, the composites could experience isothermal crystallization, which could further improve the crystallinity. With the increase of the tool temperature, the flexural strength and interlaminar shear strength were improved due to the enhanced self-adhesion of the matrix, while the Mode І fracture toughness was decreased because of the reduction of the matrix ductility. The combination of the kinetic method and experimental study was conducive to a better understanding of the crystallization mechanism and optimization of the processing conditions.
1 January 2024 in Journal of Engineered Fibers and Fabrics
Due to the short dwell time of processing temperature and pressure, the quality of the composite manufactured by AFP was not equal to the traditional processing method like autoclave or hot-press. Deeply understanding the mechanism of differences was conducive to improving the performance of the composite manufactured by AFP. In this study, the properties of high-performance carbon fiber reinforced polyphenylene sulfide (CF/PPS) thermoplastic composites manufactured by laser-assisted automated fiber placement (LAFP) in-situ consolidation and hot-press was characterized and compared. The temperature history of LAFP in situ consolidation indicated that the heating and cooling process occurred during a few seconds. And the crystallinity was only 21.6% for the laminate from LATP, while the void content was 2.75%. Due to the low crystallinity, high void content and low interlaminar bonding, the ILSS of the laminate from LAFP in situ consolidation was 34.9% lower than that of hot-press. However, the mode Ⅰ fracture toughness was 103.7% higher than hot-press.
The inter-ply sliding behavior is one of the important factors affecting the quality of carbon fiber composite products. In this paper, the inter-ply sliding behavior of the unidirectional prepreg was investigated for the preforming process. The inter-ply sliding resistance of prepreg under different conditions was measured by the homemade measuring device and the lubricating effect of inter-ply resin was identified by the micromorphology. The effect of fiber orientation was quantified by the combined roughness. With the increase of sliding distance, the inter-ply sliding resistance initially increased significantly, and finally maintained a constant value. A phenomenological model of the inter-ply sliding resistance was developed to explain the effects of pressure, velocity, and fiber orientation. This model can accurately describe the inter-ply sliding behavior of prepreg, which can be used for numerical simulation and the optimization of preforming process.
The investigation of the in-plane shear behavior of prepreg is crucial for understanding the generation of wrinkles of preforms in advanced composite manufacturing processes, such as automated fiber placement and thermoforming. Despite this significance, there is currently no standardized test method for characterizing uncured unidirectional (UD) prepreg. This paper introduces a ±45° off-axis tensile test designed to assess the in-plane shear behavior of UD carbon fiber-reinforced epoxy prepreg (CF/epoxy). Digital image correlation (DIC) was employed to quantitatively track the strains in three dimensions and the shear angle evolution during the stretching process. The influences of the temperature and stretching rate on the in-plane shear behavior of the prepreg were further investigated. The results reveal that four shear characteristic zones and wrinkling behaviors are clearly distinguished. The actual in-plane shear angle is significantly lower than the theoretical value due to fiber constraints from both the in-plane and out-of-plane aspects. When the off-axis tensile displacement (d) is less than 15.6 mm, the ±45° specimens primarily exhibit macroscale in-plane shear behavior, induced by interlaminar interface shear between the +45° ply and −45° ply at the mesoscale. The shear angle increases linearly with the d. However, when d > 15.6 mm, fiber squeezing and wrinkling begin to occur. When d > 29 mm, the in-plane shear disappears in the completely sheared zone (A). The reduction in the resin viscosity of the CF/epoxy prepreg caused by increased temperature is identified as the primary factor in lowering the in-plane shear force resistance, followed by the effect of the increasing resin curing degree. Higher shear rates can lead to a substantial increase in shear forces, eventually causing cracking failure in the prepreg. The findings demonstrate the feasibility of the test method for predicting and extracting uncured prepreg in-plane shear behaviors and the strain-rate and temperature dependency of the material response.
Wrinkles are urgent problems to be solved in the process of hot diaphragm preforming. Inter-ply slipping resistance is one of the causes of wrinkles. In this paper, based on the vertical inter-ply slipping test system, the inter-ply slipping behaviors of carbon fiber-reinforced epoxy resin composite prepregs were characterized. The mechanism of wrinkles caused by inter-ply slipping resistance was analyzed. According to the different characteristics expressed by the fiber and resin during the slip process, the inter-ply slipping behaviors of the prepregs were divided into three stages. The effect of temperature on the inter-ply slipping stresses was shown. The temperature will affect the viscosity of the prepregs. When the viscosity of the prepregs is low, the inter-ply slipping resistance will decrease. Based on the Coulomb friction law and the hydrodynamic equation, the inter-ply slipping kinetic equation of the prepregs was established. The inter-ply slipping kinetic equation was introduced into the ABAQUS main program by the ‘vfriction’ subroutine. The introduction of inter-ply slipping dynamics improved the accuracy of predicting the shape and position of wrinkles.