A reverse circulation Down-The-Hole (DTH) hammer drill bit in Casing-while-Drilling (CwD) processes is designed and applied to drilling under complicated formation. The drill bit is a special retractable drill bit with an exclusive reverse circulation gas channel. Using numerical simulations and experiments, the influence of the gas channel structure parameters of the drill bit, including the inner jet nozzles, flushing nozzles, suction channel, and other parameters, on its reverse circulation performance is analyzed, and the optimal gas channel structure parameters of the drill bit are determined to improve the reverse circulation effect. The results show that the flushing nozzles and inner jet nozzles have an important influence on entrainment performance. The entrainment rate decreases as the flushing nozzle diameter increases and decreases as the inner jet nozzle diameter increases. An increase in the suction channel diameter can improve the reverse circulation effect of the drill bit. The spiral slot drill bit is more conducive to air being sucked into the central channel in the form of spiral flow, so it can improve the entrainment performance. The entrainment rate can reach 23.4% with the optimum structured drill bit.
Air-reverse-circulation drilling into ice sheets is a promising clean technology for fast and safe ice sample recovery in the polar regions. However, a few studies in the literature explore an ice cylinder's rising from rest in tubing filled by co-current air flow. This study builds an experimental setup as well as uses the computational fluid dynamics (CFD) method to characterize the process of ice cylinder rising from being seated at bottom. Variations of the drag coefficient when a cylinder starts to rise and the critical velocity, i.e., the minimum air injection velocity to raise a cylinder, are investigated with the experiments and simulations. Reynolds number is found to have a marginal effect on the drag coefficient and critical velocity while ice-cylinder-pipe geometry can influence the two factors. Wall effect resulting from the existence of pipe lateral wall can enhance the drag coefficient and accordingly, reduce critical velocity. Decreasing the clearance between cylinder and pipe or increasing cylinder length is observed to strengthen the wall effect, but enlarging the cylinder diameter surprisingly weakens the wall effect. A mathematical correlation is developed to quantify the interplay between cylinder-pipe geometry and critical velocity by using parameters like sphericities and diameter ratio. When a cylinder continues to rise off bottom, its drag coefficient would first increase quickly and then decrease gradually to a value where terminal velocity is achieved.
Ice core drilling with air reverse circulation is a promising technology that uses high-speed airflow to transport the ice core from the bottom of the hole along the central passage of the drill pipe to the surface. Understanding how the ice core moves through the pipe is crucial for this technology in order to calculate the pneumatic parameters. In this paper, experimental study and the CFD dynamic mesh technique are used to analyze the ice core transport process and flow field characteristics. In order to prove the correctness of the dynamic mesh technique, the simulation results were verified with the experimental results, and it was found that all the simulation data were in agreement with the experimental data trend, and the maximum error was less than 10%. According to the study, once the ice core’s velocity reaches its maximum throughout the transport process, it does not change. The ice core’s maximum velocity increases with the diameter ratio and decreases with the length-to-diameter ratio, while eccentricity has no impact on the maximum velocity. When the air velocity reaches 21 m/s, the diameter ratio for the ice core with a length-to-diameter ratio of 2 increases from 0.80 to 0.92, and the maximum velocity increases from 8.92 m/s to 17.45 m/s. Data fitting demonstrates that the equation describes the relationship between the ice core’s maximum velocity, , and air velocity, . Finally, we obtain the ice core’s suspension velocity model using CFD simulation to calculate the suspension velocity, .
Due to its high mechanical penetration rate and lack of pollution of the environment, air reverse circulation drilling is considered to be a promising method for ice drilling. The air reverse circulation is caused by the combination of the ejector and the flushing nozzles in the drill bit. In this paper, CFD software was used to simulate the influence of the structure of the swirler on the effect of air reverse circulation in the swirling drill bit, and a testing stand was established for the testing of air reverse circulation. The results show that for drill bits without flushing nozzles, the smaller the helical angle is, the larger the entrainment ratio will be, meanwhile the smaller the area ratio is, the larger the entrainment ratio will be. In contrast, for drill bits designed with flushing nozzles, the larger the helical angle is, the larger the entrainment ratio will be, and the larger the area ratio is, the larger the entrainment ratio will be. In addition, the presence of the ice core sharply reduces the effect of air reverse circulation. When the ice core’s height exceeds that of the outlet of the swirler, the reverse circulation effect is slightly improved.
About Me
Mengke Wang is currently studying for a doctorate in geological engineering in the School of Construction Engineering, Jilin University. His research fields are polar and marine drilling.
Mengke Wang is currently studying for a doctorate in geological engineering in the School of Construction Engineering, Jilin University. His research fields are polar and marine drilling.