The undrained shear strength of organic soils can be evaluated based on measurements obtained from the dilatometer test using single- and multi-factor empirical correlations presented in the literature. However, the empirical methods may sometimes show relatively high values of maximum relative error. Therefore, a method for evaluating the undrained shear strength of organic soils using artificial neural networks based on data obtained from a dilatometer test and organic soil properties is presented in this study. The presented neural network, with an architecture of 5-4-1, predicts the normalized undrained shear strength based on five independent variables: the normalized net value of a corrected first pressure reading (po − uo)/σ′v, the normalized net value of a corrected second pressure reading (p1 − uo)/σ′v, the organic content Iom, the void ratio e, and the stress history indictor (oc or nc). The neural model presented in this study provided a more reliable prediction of the undrained shear strength in comparison to the empirical methods, with a maximum relative error of ±10%.
16 May 2012 in Marine Georesources & Geotechnology
The re-suspension method consists of (1) dispersion of the sediment by air-water jets, (2) pumping of the suspension (small particles and organic matter), (3) settlement in a tank, (4) filtration and (5) disposal of solids (followed by incineration in this case). The pilot test was performed to clean up an area of 3000 m2. The dispersed depth of the bottom was approximately 50 cm. The time spent for the work was two weeks. The amount of re-suspended solid removed from the bottom was about 8 tonnes in dry mass. Since the solids contain high concentrations of chemical oxygen demand (COD), total phosphorous (T-P), total nitrogen (T-N) and sulfides, the remaining sediment was considerably improved. Quantitative analyses showed that the full-scale implementation would enable the removal of about 10% of the re-suspended solids, and reduce COD by 95%, T-P by 50%, T-N by 100% and sulfide by 75% for re-deposited sediments in comparison to the original sediments.
The estimation of optical density (OD) with viable cells is challenging for engineering purposes. In this study, the OD conversion based on previous study was used. The inhibited and retarded behavior of the microbially induced carbonate precipitation (MICP) process was examined. The experimental results showed that high Ca2+ drastically influences the inhibited and retarded behavior on MICP processes. The analysis showed that the inhibition and retardation effects occurred when the Ca2+/OD loading rate exceeded 8.46 M. The critical value was equal to the proportional constant for obtaining carbonate precipitation rate (CPR) from OD. Due to this, the blending design of materials became possible, with no risk of inhibition. In conclusion, the inhibition and retardation of the MICP process are governed by the Ca2+ load and the linear standard line (LSL), which may be attributed to the capacity or tolerance of viable cells, i.e., CPR/OD = 8.46 M or Ca2+/OD = 8.46 M.
The engineering practices for applying the microbial precipitation of carbonates require a design of the blending biocement solution (BCS). The BCS is usually blended with concentrated strains NO-A10, reaction media, such as urea and CaCl2, and a solvent, i.e., water or seawater. To characterize the BCS, the unknown microbial characteristics, such as the cell viability, are complex factors. Therefore, the optical density (OD) was redefined as Rcv OD*, in which OD* was the tentative OD of the BCS used and Rcv was the conversion rate concerning the cell viability. To determine Rcv values, a standard precipitation curve based on the precipitation rate at 24 h was determined. It was found that the curve was expressed by λ1 OD+ λ2 OD2, in which λ1 and λ2 were 8.46 M and −17.633 M, respectively. With this, the Rcv and OD values of unknown BCS were estimated from the results of precipitation tests using arbitrary OD* values. By extending the testing time, the second order term of OD or OD* was negligible. Accordingly, the precipitation amount is expressed as 8.46 OD, in which the OD can be estimated by precipitation tests using arbitrary OD* values of BCSs. Unless the Ca2+ value is dominant, the optimum blending of BCS can be determined by OD. Thus, it is concluded that the blending design of BCS is achieved using 8.46 OD, or 8.46 Rcv OD*, and the standard precipitation curve was defined in this study.