Svenja Isabell Stiber

Mrs. Svenja Isabell Stiber

German Aerospace Center e.V. (DLR)
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 October 2021 in Energy & Environmental Science
Verified
Journal Article
Open access
PDF file
Svenja Isabell StiberSvenja Isabell Stiber
Svenja Isabell Stiber
NSN. Sata
N. Sata
TMT. Morawietz
T. Morawietz
SAS. A. Ansar
S. A. Ansar
TJT. Jahnke
T. Jahnke
KFK. Andreas Friedrich
K. Andreas Friedrich
Proton exchange membrane water electrolysis (PEMWE) is the most promising technology for sustainable hydrogen production. However, it has been too expensive to compete with current state-of-the-art technologies due to the high cost of titanium bipolar plates (BPPs) and porous transport layers (PTLs). Here, we report a high-performance, durable and low-cost PEMWE cell with coated stainless steel (ss) BPPs and PTLs. When using uncoated ss components in the PEMWE cell, the cell depolarizes rapidly, reaching 2 V at only 0.15 A cm−2. After the application of non-precious metal coatings of Ti and Nb/Ti on the ss-BPP and ss-PTL, respectively, the current density can be increased by a factor of 13 while maintaining the same performance. Extensive physical and electrochemical characterization supported by pore network modelling shows that the Nb/Ti coating on the ss-PTL leads to efficient water and gas transport at the interface with the anode. The PEMWE cell with coated ss components was evaluated in an accelerated stress test (AST) for more than 1000 h. No sign of Fe contamination in either the membrane or the electrodes is observed at the end of the test. With our results, we demonstrate that PEMWE cells can be manufactured almost entirely in ss, facilitating an unprecedented cost reduction in this technology and advancing the widespread use of green H2.

24 December 2022 in Nature Communications
Verified
Journal Article
Open access
PDF file
Maria RetuertoMaria Retuerto
Maria Retuerto
LPLaura Pascual
Laura Pascual
JTJorge Torrero
Jorge Torrero
MSMohamed Abdel Salam
Mohamed Abdel Salam
ÁTÁlvaro Tolosana-Moranchel
Álvaro Tolosana-Moranchel
SRSergio Rojas
Sergio Rojas
Proton exchange membrane water electrolysis is a promising technology to produce green hydrogen from renewables, as it can efficiently achieve high current densities. Lowering iridium amount in oxygen evolution reaction electrocatalysts is critical for achieving cost-effective production of green hydrogen. In this work, we develop catalysts from Ir double perovskites. Sr2CaIrO6 achieves 10 mA cm−2 at only 1.48 V. The surface of the perovskite reconstructs when immersed in an acidic electrolyte and during the first catalytic cycles, resulting in a stable surface conformed by short-range order edge-sharing IrO6 octahedra arranged in an open structure responsible for the high performance. A proton exchange membrane water electrolysis cell is developed with Sr2CaIrO6 as anode and low Ir loading (0.4 mgIr cm−2). The cell achieves 2.40 V at 6 A cm−2 (overload) and no loss in performance at a constant 2 A cm−2 (nominal load). Thus, reducing Ir use without compromising efficiency and lifetime.

3 July 2021 in Advanced Energy Materials
Verified
Journal Article
Open access
PDF file
Svenja Isabell StiberSvenja Isabell Stiber
Svenja Isabell Stiber
HBHarald Balzer
Harald Balzer
AWAstrid Wierhake
Astrid Wierhake
FWFlorian Josef Wirkert
Florian Josef Wirkert
JRJeffrey Roth
Jeffrey Roth
KFKaspar Andreas Friedrich
Kaspar Andreas Friedrich
Hydrogen produced via water electrolysis powered by renewable electricity or green H2 offers new decarbonization pathways. Proton exchange membrane water electrolysis (PEMWE) is a promising technology although the current density, temperature, and H2 pressure of the PEMWE will have to be increased substantially to curtail the cost of green H2. Here, a porous transport layer for PEMWE is reported, that enables operation at up to 6 A cm−2, 90 °C, and 90 bar H2 output pressure. It consists of a Ti porous sintered layer (PSL) on a low‐cost Ti mesh (PSL/mesh‐PTL) by diffusion bonding. This novel approach does not require a flow field in the bipolar plate. When using the mesh‐PTL without PSL, the cell potential increases significantly due to mass transport losses reaching ca. 2.5 V at 2 A cm−2 and 90 °C. On the other hand, the PEMWE with the PSL/mesh‐PTL has the same cell potential but at 6 A cm−2, thus increasing substantially the operation range of the electrolyzer. Extensive physical characterization and pore network simulation demonstrate that the PSL/mesh‐PTL leads to efficient gas/water management in the PEMWE. Finally, the PSL/mesh‐PTL is validated in an industrial size PEMWE in a container operating at 90 bar H2 output pressure.

22 February 2022 in Materials
Verified
Journal Article
Open access
PDF file
Andrea KellenbergerAndrea Kellenberger
Andrea Kellenberger
NVNicolae Vaszilcsin
Nicolae Vaszilcsin
DDDelia-Andrada Duca
Delia-Andrada Duca
MDMircea Laurențiu Dan
Mircea Laurențiu Dan
NDNarcis Duteanu
Narcis Duteanu
KFK. Andreas Friedrich
K. Andreas Friedrich
For proton exchange membrane water electrolysis (PEMWE) to become competitive, the cost of stack components, such as bipolar plates (BPP), needs to be reduced. This can be achieved by using coated low-cost materials, such as copper as alternative to titanium. Herein we report on highly corrosion-resistant copper BPP coated with niobium. All investigated samples showed excellent corrosion resistance properties, with corrosion currents lower than 0.1 µA cm−2 in a simulated PEM electrolyzer environment at two different pH values. The physico-chemical properties of the Nb coatings are thoroughly characterized by scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS), X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM). A 30 µm thick Nb coating fully protects the Cu against corrosion due to the formation of a passive oxide layer on its surface, predominantly composed of Nb2O5. The thickness of the passive oxide layer determined by both EIS and XPS is in the range of 10 nm. The results reported here demonstrate the effectiveness of Nb for protecting Cu against corrosion, opening the possibility to use it for the manufacturing of BPP for PEMWE. The latter was confirmed by its successful implementation in a single cell PEMWE based on hydraulic compression technology.

2 January 2024 in Chemie Ingenieur Technik
Verified
Journal Article
Open access
Svenja Isabell StiberSvenja Isabell Stiber
Svenja Isabell Stiber
AGAldo Saul Gago
Aldo Saul Gago
KFK. Andreas Friedrich
K. Andreas Friedrich
For renewable hydrogen production, polymer electrolyte membrane water electrolysis is the most promising technology. However, the technology is not yet competitive with conventional hydrogen production in terms of cost. The impact of cost reduction options on CAPEX and OPEX is investigated. Depending on the hours of operation, the main cost factor is the production and manufacturing of components or the price of electricity. Clearly a tremendous need to implement low‐cost electrolysis cells on a large scale to bring green hydrogen production costs to a level 1–3 € kg −1 hydrogen.