Impacting dynamics of compound droplets consisting of oil and water–glycerol mixture transitions from spreading to splashing with an increasing volumetric oil-mixture ratio. The transition to splashing is directly related to the dynamics of the ejecting lamella upon impact. Here, we present a detailed study of the ejecting lamella at the early stage of the impact. We experimentally characterize the ejection velocity and time of the ejecting lamella for a wide range of impacting velocities, volumetric oil ratios, and viscosities of the mixture. We show that ejecting dynamics depends significantly on the volumetric oil-mixture ratio, while it is slightly affected by the viscosity of the mixture. We also propose and verify experimentally a predictive model for the ejection velocity and time of the lamella.
A liquid droplet hovering on a hot solid surface is commonly referred to as a Leidenfrost droplet. In this study, we discover that a Leidenfrost droplet spontaneously performs a series of distinct oscillations as it shrinks during the span of its life. The oscillation first starts out erratically, followed by a stage with stable frequencies, and finally turns into periodic bouncing with signatures of a parametric oscillation and occasional resonances. The last bouncing stage exhibits nearly perfect collisions. We showed experimentally and theoretically the enabling effects of each oscillation mode and how the droplet switches between such modes. We finally show that these spontaneous oscillation modes and the conditions for transitioning between modes are universal for all tested combinations of liquids and surfaces.
We experimentally investigate the transpiration cooling characteristics of a porous material, sintered wire mesh. Three samples with different porosities in a plain weave structure are tested with various blowing ratios in an open-loop wind tunnel with a heated mainstream flow. The temperature on the surface of the porous material is measured by an infrared camera to obtain the cooling efficiency. The measurements reveal nonuniform distributions of the surface temperature and the cooling efficiency in both the flow direction and the transverse direction. The averaged cooling efficiency on the surface first decreases and then increases with the blowing ratio, but increases and then decreases with the porosity of the material. The internal cooling by forced convection and its combination with the external film cooling from the transpiration cooling are considered to be attributed to those two cooling characteristics, respectively. Finally, we propose a modified blowing ratio to collapse the minima of the blowing ratio for all tested samples, providing an universal transition for the decreasing and increasing branches for all tested samples in the relation between averaged cooling efficiency and blowing ratio.
Droplet impact on rotating surfaces experiences the tangential shear force from the rotating surface, generating a centrifugal force that either enhances the spreading or destabilizes the expanding lamella. In this study, we experimentally characterize the impact of a water droplet on rotating surfaces with various wettabilities, and theoretically analyze the observed impacting dynamics, including the enhanced spreading and the transition to the destabilization of the expanding lamella. Liquids with a wide range of viscosity are tested to explore the effect of liquid viscosity on the impacting dynamics. We propose a simplified approach to predict the tangential velocity induced by the surface's tangential shear force, and validate the predicted velocity by flow field measurement. We further deduce a quantitative description for the maximum spreading factor in the spreading regime, and derive the critical condition for the destabilization of the lamella for a water droplet. Good agreements are found between the predicted values and the measured ones for the impact on the rotating surfaces with various wettabilities.
Particle deposition on film cooling surface is an engineering issue that degrades the thermal protection of turbine blade. Here, we present a combined experimental and numerical investigation on the particle deposition in the vicinity of multiple film cooling holes to reveal the effect of interactions between cooling outflows on particle deposition. The numerical simulation of film cooling with a group of three rows of straight film cooling holes is conducted and validated by experimental data with blowing ratios ranging from 0 to 0.08. Wax particles with size range from 5 to 40 μm are added in the heated mainstream to simulate the particle deposition in the experiment. The simulation results show the decrease of particle deposition with blowing ratio and various deposition characteristics in different regions of the surface. The flow fields from numerical results are analyzed in detail to illustrate deposition mechanism of the particles in different regions under the interactions of cooling outflows. The cooling air from the holes in the first row reduces the particle concentration near the wall but causes particle deposition in or between the tail regions by the generated flow disturbance. The cooling air from the latter hole separates the diluted flow in the upstream from the wall, and creates a tail region without particle deposition. This revealed particle deposition characteristics under the effect of outflows interaction can benefit the understanding of particle deposition in engineering applications, where multi-row of cooling holes are utilized.