Xiang Luo

Xiang Luo


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2012 in Scientometrics
Verified
Journal Article
Closed access
PDF file
BDBensi Dong
Bensi Dong
GXGuoqiang Xu
Guoqiang Xu
XLXiang Luo
Xiang Luo
YCYi Cai
Yi Cai
WGWei Gao
Wei Gao

16 March 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
YPYubo Peng
Yubo Peng
GXGuoqiang Xu
Guoqiang Xu
XLXiang Luo
Xiang Luo
JHJian He
Jian He
DLDongdong Liu
Dongdong Liu
We experimentally investigate the transpiration cooling characteristics of a porous material, sintered wire mesh. Three samples with different porosities in a plain weave structure are tested with various blowing ratios in an open-loop wind tunnel with a heated mainstream flow. The temperature on the surface of the porous material is measured by an infrared camera to obtain the cooling efficiency. The measurements reveal nonuniform distributions of the surface temperature and the cooling efficiency in both the flow direction and the transverse direction. The averaged cooling efficiency on the surface first decreases and then increases with the blowing ratio, but increases and then decreases with the porosity of the material. The internal cooling by forced convection and its combination with the external film cooling from the transpiration cooling are considered to be attributed to those two cooling characteristics, respectively. Finally, we propose a modified blowing ratio to collapse the minima of the blowing ratio for all tested samples, providing an universal transition for the decreasing and increasing branches for all tested samples in the relation between averaged cooling efficiency and blowing ratio.

4 February 2014 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
ZTZhi Tao
Zhi Tao
DZDa Zhang
Da Zhang
XLXiang Luo
Xiang Luo
GXGuoqiang Xu
Guoqiang Xu
JHJianqiao Han
Jianqiao Han
This paper has experimentally and numerically studied the windage heating in a shrouded rotor-stator disk system with superimposed flow. Temperature rise in the radius direction on the rotating disk is linked to the viscous heating process when cooling air flows through the rotating component. A test rig has been developed to investigate the effect of flow parameters and the gap ratio on the windage heating, respectively. Experimental results were obtained from a 0.45 m diameter disk rotating at up to 12,000 rpm with gap ratio varying from 0.02 to 0.18 and a stator of the same diameter. Infrared temperature measurement technology has been proposed to measure the temperature rise on the rotor surface directly. The PIV technique was adapted to allow for tangential velocity measurements. The tangential velocity data along the radial direction in the cavity was compared with the results obtained by CFD simulation. The comparison between the free disk temperature rise data and an associated theoretical analysis for the windage heating indicates that the adiabatic disk temperature can be measured by infrared method accurately. For the small value of turbulence parameter, the gap ratio has limited influence on the temperature rise distribution along the radius. As turbulence parameter increases, the temperature rise difference is independent of the gap ratio, leaving that as a function of rotational Reynolds number and throughflow Reynolds number only. The PIV results show that the swirl ratio of the rotating core between the rotor and the stator has a key influence on the windage heating.

19 December 2013 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
XLXiang Luo
Xiang Luo
DZDa Zhang
Da Zhang
ZTZhi Tao
Zhi Tao
GXGuoqiang Xu
Guoqiang Xu
QWQianshun Wang
Qianshun Wang
This paper has experimentally studied the windage torque in a rotor-stator system with superimposed central inflow and rotor-mounted protrusions. A novel measurement method has been proposed, and the basic principle is to transform the torque of rotating components into static torque measured by using a static torquemeter. Compared with the previous research, the difference of the moment coefficient for the free plain disk in this paper is within 10%. The disk models used in the experiments included a plain disk and a rotor with 18 protrusions. Plain-disk results were obtained with axial clearances varying from 4.5 mm to 40.5 mm and a stator of the same diameter. Two test cases were performed: one was the case where the flow structure was dominated by the superimposed flow and the other was where rotation dominated the flow structure. For the plain-disk case, as turbulence parameter increases, the sensitivity of the torque to variations of G value also increases, leaving the moment coefficient as a function of the rotational and throughflow Reynolds number only. Comparing to the flow parameter, gap ratio and shroud-clearance ratio have weaker influence on frictional moment coefficient. The rotor with protrusions results showed that the gap ratio had negligible effect on the moment coefficient for the former case; however, the torque decreased by approximately 20% with the decrease of the gap ratio for the latter case. It was also found that, for different configurations, the deviation in the moment coefficient was attributed to variations in form drag. In addition, the moment coefficient was affected by the orientation of bolts with respect to the direction of rotation. The empirical correlations have been proposed for the windage losses of various bolt configurations, and a further discussion about minimizing the windage losses was conducted.

2 August 2024 in Chinese Journal of Aeronautics
Verified
Journal Article
Open access
ZWZeyu Wu
Zeyu Wu
DLDongdong Liu
Dongdong Liu
SWSipeng Wang
Sipeng Wang
ZZZhe Zhang
Zhe Zhang
YBYang Bai
Yang Bai
XLXiang Luo
Xiang Luo
In modern aero-engine, the turbine rim seals whose purpose is to reduce the ingress are located in a complex flow region between the mainstream and secondary air flows. The sealing air discharged from the compressor of engine is used to purge turbine cavity. In order to examine the effects of ingress through four distinct rim seals, a one-stage test rig was used in the experiments presented in this work. At a Reynolds number of 5.16×105 in the mainstream and (0.85-2.13)×106 in the rotational, the radial pressure distribution on the stator was determined. To assess flow characteristics and sealing efficacy, measurements of the swirl ratio and CO2 concentration were made. The reliability of turbine rim-seals is determined by the locations of the hook and teeth, as well as their effect on hot gas ingestion. To evaluate the performance of four types of seals: a datum double-rim seal and three derivatives with different clearances, the data are employed. Due to the inlet air position, the swirl ratio exhibited a pronounced inflection for all the rim seals. The sealing efficiency can be decreased by putting the hook closer to the rim or by taking the teeth out. Static pressure measurements in the turbine cavity indicate that the seal position has a significant impact. The analysis results revealed that the existence of slot vortex is beneficial to improving efficiency.

8 June 2023 in Aerospace
Verified
Journal Article
Open access
PDF file
ZZZhe Zhang
Zhe Zhang
ZWZeyu Wu
Zeyu Wu
XLXiang Luo
Xiang Luo
WLWeitong Liu
Weitong Liu
The traditional blade cooling method can no longer meet the requirements of high cooling efficiency in modern engines. In order to solve this cooling problem, this paper proposes cooling turbine guide blades based on liquid metal. The feasibility was preliminarily verified using a one-dimensional heat conduction model. Then, using a numerical method, we found that the cooling effect of liquid metal is much better than that of air cooling. The main reason for its good cooling effect is that the heat transfer coefficient of liquid metal reaches a magnitude of tens of thousands. Moreover, as the inlet temperature of the liquid metal decreases and the inlet Reynolds number increases, the liquid cooling effect becomes better. The definition of the heat transfer quality factor can reflect the reasons for the influence of the inlet temperature of the liquid metal.