Integrity is one criteria to evaluate GNSS performance, which was first introduced in the aviation field. It is a measure of trust which can be placed in the correctness of the information supplied by the total system. In recent years, many GNSS-based applications emerge in the urban environment including liability critical ones, so the concept of integrity attracts more and more attention from urban GNSS users. However, the algorithms developed for the aerospace domain cannot be introduced directly to the GNSS land applications. This is because a high data redundancy exists in the aviation domain and the hypothesis that only one failure occurs at a time is made, which is not the case for the urban users. The main objective of this paper is to provide an overview of the past and current literature discussing the GNSS integrity for urban transport applications so as to point out possible challenges faced by GNSS receivers in such scenario. Key differences between integrity monitoring scheme in aviation domain and urban transport field are addressed. And this paper also points out several open research issues in this field.
Reliable GPS positioning in city environment is a key issue: actually, signals are prone to multipath, with poor satellite geometry in many streets. Using a 3D urban model to forecast satellite visibility in urban contexts in order to improve GPS localization is the main topic of the present article. A virtual image processing that detects and eliminates possible faulty measurements is the core of this method. This image is generated using the position estimated a priori by the navigation process itself, under road constraints. This position is then updated by measurements to line-of-sight satellites only. This closed-loop real-time processing has shown very first promising full-scale test results.
10 June 2020 in IEEE Intelligent Transportation Systems Magazine
Urban positioning using the Global Positioning System (GPS) is challenging because of multipath. Urban canyons limit open sky visibility, and cause signal reflection and diffraction, resulting in significant satellite range measurement errors. The investigations reported here have been carried out in a French project calledInturb(an acronym derived from integrity and urban positioning). So far, the project has had two phases: first, a simple Three-Dimensional (3D) geometrical city modelling, called “Urban Trench”, has been developed and engineered manually from data sets collected in different cities. Positioning improvement in terms of accuracy was quantified where the model could be applied. Second, this modelling has been automated, based on the standard national BD Topo ® map database for France, with promising results. This geometrical modelling makes it possible to distinguish between line-of-sight satellite signals and those from non-line-of-sight. The latter, apparentlybona fide, signals are caused by strong reflections, usually from buildings with a lot of steel and glass in their construction. A correction of the pseudo-range measurements of the latter is also computed and applied in the position estimator. Positioning accuracy is improved, whilst availability is kept at its maximum. In the study both manual and automatic 3D models are used in extensive experimental campaigns. Results are: first, the possibility to cover entirely any urban area in the country; second, the reduction of the median error in 3D by more than 50% on data collected in Nantes, Paris and Toulouse for a total duration of nearly ten hours; third, the compliance with standards used in most embedded maps and geographical information systems, including an assessment of the trade-off between the model simplicity and the positioning improvement.
16 September 2016 in NAVIGATION: Journal of the Institute of Navigation
The lane-level localization of vehicles with low-cost sensors is a challenging task. In situations in which Global Navigation Satellite Systems (GNSSs) suffer from weak observation geometry or from the influence of reflected signals, the fusion of heterogeneous information presents a suitable approach for improving the localization accuracy. We propose a solution based on a monocular front-facing camera, a low-cost inertial measurement unit (IMU), and a single-frequency GNSS receiver. The sensor data fusion is implemented as a tightly coupled Kalman filter that corrects the IMU-based trajectory with GNSS observations while employing European Geostationary Overlay Service correction data. Further, we consider vision-based complementary data that serve as an additional source of information. In contrast to other approaches, the camera is not used to infer the motion of the vehicle, but rather for directly correcting the localization results under the usage of map information. More specifically, the so-called camera-to-map alignment is done by comparing virtual 3D views (candidates) created from projected map data with lane geometry features that are extracted from the camera image. One strength of the proposed solution is its compatibility with state-of-the-art map data, which are publicly available from different sources. We validate the approach on real-world data recorded in The Netherlands and show that it presents a promising and cost-efficient means to support future advanced driver assistance systems.