Electrolytic plasma polishing technology is widely used in medical devices, aerospace, nuclear industry, marine engineering, and other equipment manufacturing fields, owing to its advantages of shape adaptability, high efficiency, good precision, environmental protection, and non-contact polishing. However, the lack of in-depth research on the material removal mechanism of the electrolytic plasma polishing process severely restricts the regulation of the process parameters and polishing effect, leading to optimization and improvement by experimental methods. Firstly, the formation mechanism of passivation film was revealed based on an analysis of the surface morphology and chemical composition of stainless steel. Subsequently, the dissolution mechanism of the passivation film was proposed by analyzing the change in the valence state of the main metal elements on the surface. In addition, the surface enclosure leveling mechanism of electrolytic plasma polishing (EPP) for stainless steel was proposed based on a material removal mechanism model combined with experimental test methods. The results show that EPP significantly reduces the surface roughness of stainless steel, with Ra being reduced from 0.445 µm to 0.070 µm. Metal elements on the anode surface undergo electrochemical oxidation reactions with reactive substances generated by the gas layer discharge, resulting in the formation of passivation layers of metal oxides and hydroxides. The passivation layer complexes with solvent molecules in the energetic plasma state of the gas layer with SO42− ions, forming complexes that enter the electrolyte. The dynamic balance between the formation and dissolution of the passivation film is the key to achieving a flat surface. This study provides theoretical guidance and technical support for the EPP of stainless steel.
26 March 2024 in IEEE Transactions on Antennas and Propagation
We present a miniaturized and laminated metamaterial (MM) block, which is formed using an extremely compact stacked unit cell consisting of a double-layer spiral connected in series with a chip capacitor, with a lateral size on the order of 1/20000 of the operating wavelength. The unit cell enables the construction of an MM sample with an operating frequency as low as 325 kHz, provided a 1.8 nF capacitor and the stacking compactness is configured as 1.05. A RLC circuit simulation method is proposed to extract the relative permeability of the low-frequency MM block with three-dimensional layout, which eliminates the wave-port configuration and two-dimensional boundary limitations. Experiments confirm that the proposed MM block has enhanced resonant strength at lower resonant frequencies. Efficiency measurements performed for a wireless power transmission (WPT) prototype reveal 34.5% enhancement of the power transmission efficiency (PTE) at a 120 mm working distance using the fabricated MM sample, which is nearly three times that of the original prototype. In addition, the anti-misalignment performance of the coils is tested at a 100 mm distance, revealing an enhanced misalignment tolerance of 58.3% using the MM sample when the target PTE is set to 80% that of the alignment case. This excellent performance and compact size make the proposed laminated MM block extremely attractive for many low-frequency WPT applications with limited dimensions, such as telemetry systems for rotating machineries.
This paper proposes a wireless passive measurement system that supports real-time signal acquisition, multi-parameter crosstalk demodulation, and real-time storage and calculation. The system consists of a multi-parameter integrated sensor, an RF signal acquisition and demodulation circuit, and a multi-functional host computer software. The sensor signal acquisition circuit uses a wide frequency detection range (25 MHz–2.7 GHz) to meet the resonant frequency range of most sensors. Since the multi-parameter integrated sensors are affected by multiple factors, such as temperature and pressure, there will be interference between them, so the algorithm for multi-parameter decoupling is designed, and the software for sensor calibration and real-time demodulation is developed to improve the usability and flexibility of the measurement system. In the experiment, temperature and pressure dual-reference integrated surface acoustic wave sensors in the condition of 25–550 °C and 0–700 kPa are used for testing and verification. After experimental testing, the swept source of the signal acquisition circuit can meet the output accuracy in a wide frequency range, and the detection result of the sensor dynamic response is consistent with that of the network analyzer, with a maximum test error of 0.96%. Furthermore, the maximum temperature measurement error is 1.51%, and the maximum pressure measurement error is 5.136%. These results indicate that the proposed system has good detection accuracy and demodulation performance, and it can be used for multi-parameter wireless real-time detection and demodulation.
7 March 2025 in IEEE Transactions on Power Electronics
Current simultaneous wireless power and signal transmission (SWPST) systems have a rather limited transmission distance because the power transmission efficiency (PTE) and signal transmission gain (STG) decrease rapidly with increasing distance. To address this issue, a novel miniaturized hybrid metamaterial block (HMB) with negative and near-zero permeability is designed based on two types of compact metamaterial stacks. Depending on the magnetic field boundary conditions, the magnetic fields for transmitting power and signal can be more confined between the coupling coils, thus enhancing the PTE and STG. An optimization design method for miniaturizing the metamaterials stacks is presented, achieving enhanced Q factors at low resonant frequencies. Furthermore, a resonant hybridization analysis method is proposed to achieve the target resonant frequencies of the metamaterial stacks and the miniaturization of the overall HMB. Finally, an SWPST prototype with dual-sided LCCL compensation networks is built, demonstrating a 16.3% improvement in the PTE and 11.8-dB enhancement in the STG at a 14-cm distance. The enhancement of the signal-to-noise ratio (SNR) from −6 to 2.2 dB enables data flowing at a 400-kb/s rate to be recovered. These results show that the proposed HMB can simultaneously improve the PTE and SNR over a longer transmission distance.
13 January 2025 in IEEE Transactions on Instrumentation and Measurement
As aerospace technology continues to advance, real-time monitoring of heat flux density has become increasingly important. However, most heat flux sensors (HFSs) are unable to withstand high temperatures without water cooling, resulting in their sensitive layer films being exposed to severe oxidation or sublimation. This paper proposes a composite protective layer thin-film heat flux sensor (TFHFS) based on an ITO/In₂O₃ thermopile. An Al₂O₃-YSZ protective layer is deposited on top of the sensitive layer to mitigate sublimation failures caused by prolonged exposure to high temperatures. Test results indicate that the temperature resistance of the TFHFS with the protective layer is significantly enhanced, enabling it to withstand a maximum temperature of 1200 °C, with response and recovery times of 1.2 s and 1.3 s, respectively. Furthermore, the fabricated TFHFS exhibited excellent repeatability and high-temperature stability. However, the reliability of the leads in the designed TFHFS requires further enhancement in future studies.
14 May 2025 in IEEE Transactions on Instrumentation and Measurement
Real-time monitoring of component deformation under conditions of elevated temperature and high rotational speeds is essential for maintaining the structural integrity and operational safety of machinery. Conventional Surface Acoustic Wave (SAW) strain sensors exhibit limitations, including insufficient operating temperature capabilities and reduced measurement accuracy, which hinder their applicability under extreme conditions. This study developed a highly sensitive SAW strain sensor based on Langasite (LGS) and a beam-plate structure. The fabrication process employed a double-sided lithography wet etching technique to produce a beam-plate structure with a smooth surface, achieving a surface roughness of 0.945 nm — an 88.9% reduction from the roughness of 8.53 nm typically obtained using single-sided lithography. Interdigital electrode patterns were etched onto both the beam-plate and conventional LGS substrates using Micro-Electro-Mechanical Systems (MEMS) technology. The sensor was evaluated on a custom-designed high-temperature strain test platform. The results demonstrated that the beam-plate type SAW strain sensor operated stably across a temperature range of 25 °C-850 °C and a strain range of 0-1600 μƐ. The sensor exhibited a sensitivity of 550 Hz/μƐ at room temperature, which was approximately 3.14 times higher than that of conventional SAW sensors. Under the concurrent effects of temperature and strain at elevated temperatures, a temperature-strain decoupling algorithm was developed, yielding a maximum error between the decoupled and measured values ranging from -4.4% to +4.3%. The beam-plate type SAW strain sensor is characterized by its high sensitivity, excellent temperature resistance, rapid response time, and robust anti-interference properties. Thus, the proposed sensor is well-suited for applications in advanced fields such as aerospace, highend equipment, and other high-precision domains.